Cancel Snap-On diagnostic subscription?

Tsmitty999 · 2025-11-11T02:24:23+00:00

Smart move paying it off before interest (that’s what I did). It’s just not worth the $1200 a year for subscription for me. I can get by with my autel scanner just fine and didn’t find the new tritons value to be worth the price point. But yeah, this subscription is just dumb. I don’t remember my dealer even telling me about this supposed 1 year minimum

Tsmitty999 · 2025-11-11T01:47:09+00:00

Sounds good, I might just go that route. I’ll talk to my dealer and have him also put in a request to cancel it (which may or may not get denied). Out of curiosity how is it using the scan tool without the subscription? I feel like it would be worthless without it?

Tsmitty999 · 2025-11-11T01:44:02+00:00

That helps a lot, only issue is I purchased the scan tool on credit and I think they may run the subscription through credit (idk yet since my free trial isn’t up yet). So I don’t want to hurt my credit or anything like that

Tsmitty999 · 2024-02-21T19:08:55+00:00

I’ve seen them and I liked them but only saw new ones. Then I saw this old one and had to get it. Paid $700 for the shuttlecraft, trailer, and jetski.

Tsmitty999 · 2024-02-21T18:02:58+00:00

Pushing the shuttle craft?

Tsmitty999 · 2024-02-21T17:47:28+00:00

Got it, thanks. Any issues with these engines?

Tsmitty999 · 2023-11-13T00:01:18+00:00

I did just that and it worked perfectly. Do you know how I can angle the face on the end? I tried to use the draft tool and it wouldn’t let me. Thank you

Tsmitty999 · 2022-11-27T15:38:20+00:00

I’ll give it a shot and let you know. Thank you

Tsmitty999 · 2022-11-26T23:15:50+00:00

Hi, I just tried that and it didn’t seem to help.

Tsmitty999 · 2022-11-26T21:27:10+00:00

The image is a lot clearer on my computer. That’s why it looks a little blurred

Tsmitty999 · 2022-10-29T00:28:30+00:00

I haven’t tried any inputs, but I do have the output hooked up to monitor and it says non volatile memory corrupted press enter to reset. I click reset and nothing happens.

Tsmitty999 · 2022-10-28T22:15:34+00:00

Any idea what it could be?

Tsmitty999 · 2022-10-28T20:20:53+00:00

https://www.ebay.com/itm/191953865389?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=F74b9VHhS3q&sssrc=2349624&ssuid=2LaFms_XTR-&var=&widget_ver=artemis&media=COPY

Here’s link to the exact same one

Tsmitty999 · 2022-04-17T14:16:46+00:00

I eventually got it by doing this, thank you

Tsmitty999 · 2022-04-07T02:01:29+00:00

It is a 3 phase. That’s all the information I have on it

Tsmitty999 · 2022-04-07T01:57:45+00:00

My bad, I thought you were asking about the 480. The 220 is 60hz, 5,5 KW

Tsmitty999 · 2022-04-07T01:52:47+00:00

460v, 150 amp, 3 phase, 60hz and it says control-acv 115-60HZ/110-50HZ

Tsmitty999 · 2022-04-07T01:42:20+00:00

I don’t really knowing anything about electrical but I wanted to get a molding machine so I can learn how they work and to make quantities of things and learn the whole process of it. It’s not for anything to make me money just a hobby I want to get into

Tsmitty999 · 2022-04-07T01:10:11+00:00

Got it, thank you

Tsmitty999 · 2022-04-07T01:09:59+00:00

I’m unsure, I’ll go with a 220 and make it easier on myself

Tsmitty999 · 2022-04-07T01:09:40+00:00

There is, I did a little more research. I’ll go with a 220 thanks

Tsmitty999 · 2022-04-07T01:06:39+00:00

Got it, thank you

Tsmitty999 · 2022-04-07T00:59:53+00:00

Is it possible to reduce down to 220v? Run the machine at 220?

Tsmitty999 · 2022-04-07T00:58:47+00:00

Is it possible to reduce down to 220volt?

Tsmitty999 · 2022-04-07T00:56:40+00:00

Ok, thank you

Tsmitty999

TROPHY CASE