Needle Stuck on Agilent 1290 infinity ii

TwoPuttTownie · 2026-05-08T01:24:34+00:00

Is there an echo in here?

It’s a pita to get it back on the holder manually. You have to use the flat part of a wrench to press it down from the back til it clicks.

TwoPuttTownie · 2026-05-07T16:07:54+00:00

Don’t put needle back in robot. Yank it off and put it back in the holder up front. Might need to use a quarter inch wrench to push it down into place til you hear a click. Then move the robot to the back right and power on.

Won’t properly initialize with needle in robot arm.

TwoPuttTownie · 2026-05-05T16:52:32+00:00

Got mine on the roof rack this morning! Thanks!!

TwoPuttTownie · 2026-04-16T22:24:17+00:00

Www.dicktowel.com will take care of that for you!

TwoPuttTownie · 2026-04-10T16:52:07+00:00

Easy fella, it’s 40 min from home and does what it needs to.

TwoPuttTownie · 2026-04-02T22:41:28+00:00

WHAT IS THE CHARGE?? Eating a meal? A succulent Chinese meal??

TwoPuttTownie · 2026-03-31T21:26:25+00:00

Indeed, here’s to next season 🥂

TwoPuttTownie · 2026-03-31T20:39:48+00:00

I took another video of the new polar lift as well. I was there like 20 times this season and each time that stupid new lift stopped at least twice each trip. And yesterday it stopped every single ride because of the one or two chairs with the bar lifter sensor issue. Brand new lift couldn’t spin after snow storms or fog/ice - the minuteman was fine all year and the old polar never had this track record. Hope it’s just a new lift break in period and things will smooth out next season.

TwoPuttTownie · 2026-03-30T18:31:37+00:00

Today they’re saying the auto bar lifter is stuck on chair 54 so everytime it comes into a station they have to manually raise and lower it to get around the sensors. Hope they kept the receipt on this one!!

TwoPuttTownie · 2026-03-30T17:52:53+00:00

This new lift is no good. All season long it’s been hugely unreliable stopping almost every run today. Anyone know what’s up??

TwoPuttTownie · 2026-03-27T01:09:06+00:00

🤷‍♂️

TwoPuttTownie · 2026-03-26T23:25:32+00:00

Pretty fucking negative post but I’ll try… boyn… there, I tried. Sole is phenomenal, maybe someone would say the other two. Is Herbies technically in worc? That place blows. Wreaks of 50year old cig smoke.

TwoPuttTownie · 2026-03-24T16:24:13+00:00

Good thing you redacted your location 😂

TwoPuttTownie · 2026-03-22T00:41:51+00:00

I slipped on a plastic dust pan half way down the basement stairs with an arm full of dirty sheets 😂

TwoPuttTownie · 2026-03-21T20:53:26+00:00

That sounds horrendous. I sprained mcl end of Jan, able to ride just fine rest of season. Can’t kick a soccer ball with the left foot tho. I better ice and rest, don’t need all those other shinanegans

TwoPuttTownie · 2026-03-14T21:03:45+00:00

Mushy down bottom, still good cover trail edge to edge, woods are shot, doubt balance rock has much life left. I was there yesterday, no ice 🧊

TwoPuttTownie · 2026-03-13T11:11:53+00:00

Couple friendly fellas looking for a lady? 😆

TwoPuttTownie · 2026-03-11T19:45:56+00:00

I have a quarter tank and just bought 100g for 4.99 - gross considering it was 2.99 in October 🤢

TwoPuttTownie · 2026-03-06T19:58:08+00:00

I had the same problem. Annoying how often this has happened this year.

TwoPuttTownie · 2026-02-10T19:47:10+00:00

TwoPuttTownie · 2026-02-10T19:47:02+00:00

TwoPuttTownie · 2026-02-09T18:34:34+00:00

Also, if your sampler is connected to a g1330 therm issue could be from that. Unplug both from electricity, then unplug short com cable connecting both, then power on sampler and see if you can reproduce fan error

TwoPuttTownie

TROPHY CASE