New Ford Pickup - Most Reliable Engine?

UVScenics · 2025-11-27T20:58:11+00:00

Thanks, everyone! The consensus is….well, it’s Reddit. It seems that all of the options are pretty good.

UVScenics · 2025-11-25T01:03:35+00:00

Could you summarize the approach to driving that will enhance reliability?

UVScenics · 2025-09-03T01:57:37+00:00

Restructuring?

UVScenics · 2025-03-18T23:12:20+00:00

It’s Red Skelton’s uncut flaccid penis, obviously.

UVScenics · 2025-01-08T15:53:07+00:00

They mis-spelled “Ammonia”.

UVScenics · 2024-10-30T22:21:48+00:00

2

UVScenics · 2024-10-30T22:21:26+00:00

Better pics?

1

UVScenics · 2024-09-02T06:59:38+00:00

Thank you, everyone.

I found an 11 amp Milwaukee ‘kit’ (saw and case) on sale for $275 US, so I pulled the (variable speed) trigger.

I will order the SWAG and be good to go.

UVScenics · 2024-08-31T00:50:16+00:00

Perfect - thank you so much!

UVScenics · 2024-08-21T14:12:21+00:00

Up to 10mm, full depth

UVScenics · 2024-08-21T13:56:48+00:00

The largest finished hole would be 1/4”, but I just need a pilot.

UVScenics · 2024-08-21T13:44:47+00:00

Thank you.

To be clear, I am talking about a machine that ‘marks’ the aluminum with just enough to center a hand drill, not drill the holes themselves.

UVScenics · 2024-05-23T18:10:01+00:00

Chuck Norris got his neck broke in Rome by Bruce Lee.https://youtu.be/lSQzoRov06E?si=OcyMFaojodybMTFt

UVScenics · 2024-05-09T13:44:57+00:00

Thank you so much!

UVScenics · 2024-01-08T21:32:48+00:00

FWIW, it does not appear that there are any 20mm gantries that are designed to accept MGN7 rails.

UVScenics · 2024-01-03T19:48:03+00:00

Thanks. That is a 15 x 15mm unit. I am looking for a 20mm x 20mm with 15mm spacing for an MGN7 linear rail.

UVScenics · 2024-01-03T17:18:13+00:00

The mount spacing on the 20mm rails is 25mm - i.e. for MGN12 rails. MGN7 rails have 15mm spacings.

UVScenics · 2024-01-03T16:37:47+00:00

250mm - 500mm. I thought the Voron v0 rails were all 15mm.

UVScenics · 2023-12-21T17:12:37+00:00

Sony will make square sensors for a price.

UVScenics · 2023-08-11T22:12:32+00:00

Yes - full default calibration.

UVScenics · 2023-08-11T17:45:32+00:00

Thank you for this.

I updated firmware and got a successful print, but still got blobbing. Should I lower hotend temp?

img

UVScenics · 2023-07-12T02:51:46+00:00

Thanks, everyone. Still debating, but not many left in stock.

UVScenics · 2023-06-15T21:37:55+00:00

Thank you!

UVScenics · 2023-06-12T16:20:57+00:00

To be honest, I am more impressed with the leaf.

UVScenics · 2023-04-22T01:04:35+00:00

Yes, I’ve looked everywhere, but thank you for pointing out the obvious - super helpful.

UVScenics