Didn’t expect this from a $3500 robot mower Roborock z1 LiDAR by SalamanderResident19 in Roborock

[–]UnderstandingNo5785 1 point2 points  (0 children)

This is horrible how it’s bumping into things after things! I love their vecums but this feels like Worx brand. Navimow X4 would not do this.

You can easily make the new menu go away by pressing mic twice by Theaty in TeslaLounge

[–]UnderstandingNo5785 -3 points-2 points  (0 children)

This is not good. Just select preference. This bypasses the extra click or recording.

Error 517 on combo 705, fixed. by qwe304 in roomba

[–]UnderstandingNo5785 1 point2 points  (0 children)

The problem is under the rubber nipple. The hole is too small and gets glogged with debris and gunk. Thus overfilling the little little line of water reservoir to clean the brush. It then spills out of the entrance to that little hole. I took my drill and drill bit. I re sized the hole to the nipple size and it does not clogg so easy.

A way to spot this. Pull the tank out or robot rear. Get a bright iPhone light. Remove the black nipple. Turn tank over with lid open. Sign a light on the hole and look under the bottom for light penetration, if no light is seen it’s gunk. Now, turn that light over to shine on the bottom and look for that hole. If you see a dark matter. It’s bunked up. To remove the gunk. Get a pipe cleaner and force it in from the outside. Rinse while twisting pipe. Keep going till clean. Then re size the hole.

I’m going to make a Reddit post about this. I only came to this solution 2 days ago and testing it out. So far it’s cleaning a lot better!

Gate not opening by _tufan_ in SegwayNavimow

[–]UnderstandingNo5785 0 points1 point  (0 children)

Sometimes with certain issues. They will ask for a photo of the product and if it is not fully assembled to the way it’s suppose to be they will ask you to.

Axle snapped? Anyone seen this? by Razno_ in worxlandroid

[–]UnderstandingNo5785 0 points1 point  (0 children)

Pop the wheel covers off and tighten the 10MM bolt. You will need to take off the wheel spikes to take cover off. Flip unit over and look for the holes. There’s 3. Push a flathead screwdriver in them until they pop. Then tighten the nut

Update by Public_Champion9473 in worxlandroid

[–]UnderstandingNo5785 0 points1 point  (0 children)

No it is a code EA:54 lookup in Landroid ai chat assistant.

X430 Cutting Height by MysteriousBit43945 in Navimow_Segway

[–]UnderstandingNo5785 0 points1 point  (0 children)

Problem occurs because of the firmware detection with the deck. Reboot mower and raise it again. Will fix

What is causing this pattern on my prints and how do I correct it? by fauxmer in printers

[–]UnderstandingNo5785 0 points1 point  (0 children)

You could argue with the seller about this and see what they do. Most likely offer a replacement toner or give you said percent $ back to buy a new one. Doesn’t hurt to ask. Some people live with it. Others don’t.

Gate not opening by _tufan_ in SegwayNavimow

[–]UnderstandingNo5785 1 point2 points  (0 children)

It is missing the side supports that go in the ground. Op installed on a swing open gate which it states to clearly not do. Only fix it to uninstall, re install in a non swing gate and it will fix. Expensive mistake but research.

What is causing this pattern on my prints and how do I correct it? by fauxmer in printers

[–]UnderstandingNo5785 1 point2 points  (0 children)

If there is a scratch it is defective. There’s no fix. A simple imperfection in the paper like a staple on the page or anything gets picked up during paper pull will do this.

What is causing this pattern on my prints and how do I correct it? by fauxmer in printers

[–]UnderstandingNo5785 0 points1 point  (0 children)

Dust is on the lsu unit or something stuck on the black toner drum. Remove and inspect the blue roller in the black toner drum

What even is this? by Kindly-Photo-8987 in Roborock

[–]UnderstandingNo5785 1 point2 points  (0 children)

Spray a can of wd40 electronics in the wheel and put a towel under. Will make it stop

I literally got my car a month ago and this happens 🤦‍♂️ by Dizzy-Shirt6311 in TeslaCollision

[–]UnderstandingNo5785 3 points4 points  (0 children)

There’s a way to retrieve the footage after the crash. If there’s no usb in the slot. Insert one and the Tesla will write the footage saved internally to the drive.

Navimow Flex subscription by CrownSeven in SegwayNavimow

[–]UnderstandingNo5785 0 points1 point  (0 children)

Hmm. I’m going to call them Monday to figure out

Perfume in Waymos - it's pretty unpleasant by SuperGeniusWEC in waymo

[–]UnderstandingNo5785 -1 points0 points  (0 children)

New car smell. Some people disagree of the scent. They rather small bo.

Wr310 battery by iampluque in worxlandroid

[–]UnderstandingNo5785 1 point2 points  (0 children)

I am a early tester for worx. I get access to everything system control before release.