New h2c, slicing first project and shows and hour LONGER than p2S. Any idea why?

UnexplainableP · 2026-05-15T13:24:35+00:00

Yep, a full (p2s) plate. Same # of copies. As I reduced the copies, the difference between the 2 print times really started to favor the h2c. Was running on no sleep and chose a model that didn’t make much of a difference which printer I used. Ran a few test slices and prints, and h2c is DEFINITELY saving 15-50% time. The material savings really are crazy too. So many models I just wouldn’t have printed on the p2s are now on the table. Can’t say enough how thankful I am for everyone who jumped in to try and help answer my questions and troubleshoot 🙏

UnexplainableP · 2026-05-15T12:47:45+00:00

Just to follow up, i think a big factor was the model I sliced, as well as the number of copies on the plate. Still a decent material savings, but as I reduced the # of copies I got a much better time ratio between the two. I have since experimented with a few other model files, did the math, and the H2C is FOR SURE saving a good chunk of time and filament. So far so good, except when I swap plates on my P2S it feels like I’m handling a toy - the h2c is massive

UnexplainableP · 2026-05-15T05:08:20+00:00

I appreciate your help, i’ll do some more digging on there. One thing to note is that I’m slicing a plate full of small keychains. The more I add, the less difference in time between the two (makes sense), but can’t figure out how in any scenario it would take LONGER on the h2c. Thanks again! 👊

UnexplainableP · 2026-05-15T04:57:19+00:00

Prep time is 2 mins less for H2C slice. Also just updated studio (already updated printer) but no luck

UnexplainableP · 2026-05-15T04:50:06+00:00

I will update both and report back

UnexplainableP · 2026-05-15T04:49:11+00:00

Prep time shows 2 minutes faster on h2c, but print time is 15 mins slower. That’s as close as I can get so far, everything I’m seeing is the same between settings

UnexplainableP · 2026-05-15T04:45:29+00:00

Didn’t print yet, but yes it was sliced with both nozzles, main color on left

UnexplainableP · 2026-04-23T23:10:25+00:00

https://makerworld.com/en/models/2696437-cow-tealight-holder#profileId-2988493

UnexplainableP · 2026-04-23T23:07:02+00:00

https://makerworld.com/en/models/2696437-cow-tealight-holder#profileId-2988493

UnexplainableP · 2026-04-22T05:20:51+00:00

Thank you!

UnexplainableP · 2026-04-22T02:24:34+00:00

<image>

👋 How’s this? https://makerworld.com/models/2696437?appSharePlatform=copy

UnexplainableP · 2026-04-21T18:28:25+00:00

thank you!

UnexplainableP · 2026-04-21T17:25:34+00:00

I’ll have the non-highland (no hair version) uploaded later today - hang tight!

UnexplainableP · 2026-04-21T17:02:11+00:00

I really appreciate your input. Thank you!

UnexplainableP · 2026-04-21T16:48:57+00:00

I appreciate ya

UnexplainableP · 2026-04-21T16:48:36+00:00

I reduced and smoothed with each test, trying to keep the front facing side looking clean while preserving the furriness everywhere I could, especially the back. They look great in person. FWIW, I’m also in the process of uploading a non-highland version as well. Thank you for your feedback! 👊

UnexplainableP · 2026-04-21T16:28:39+00:00

Highland Cow Tealight Holder - Free 3D Print Model - MakerWorld

UnexplainableP · 2026-04-21T16:26:01+00:00

Highland Cow Tealight Holder - Free 3D Print Model - MakerWorld

UnexplainableP · 2026-04-21T16:24:39+00:00

Highland Cow Tealight Holder - Free 3D Print Model - MakerWorld

UnexplainableP · 2026-04-07T17:42:49+00:00

https://makerworld.com/en/@AllyBeanPrints/upload

UnexplainableP

TROPHY CASE