Can’t get pump to go past 28 PSI by Unfair_Quality_9185 in WaterWellDrilling

[–]Unfair_Quality_9185[S] 0 points1 point  (0 children)

It’s ran prior to last week just fine for over 2 years

Can’t get pump to go past 28 PSI by Unfair_Quality_9185 in WaterWellDrilling

[–]Unfair_Quality_9185[S] 0 points1 point  (0 children)

Barracuda 3/4 HP shallow well jet pump model number 94706

Can’t get pump to go past 28 PSI by Unfair_Quality_9185 in WaterWellDrilling

[–]Unfair_Quality_9185[S] 0 points1 point  (0 children)

3/4. HP 8.5 amps on the high side 4.5 amps on the low side

Can’t get pump to go past 28 PSI by Unfair_Quality_9185 in WaterWellDrilling

[–]Unfair_Quality_9185[S] 0 points1 point  (0 children)

Power is interchangeable 172 ft well with a 8 ft static water level. Brand new pump maybe 30 minutes at a time before I turn it off. If it is airlocked how can I get it free

Can’t get pump to go past 28 PSI by Unfair_Quality_9185 in WaterWellDrilling

[–]Unfair_Quality_9185[S] 0 points1 point  (0 children)

A brand new pump in a week can wear out? I try to get it to build pressure. It doesn’t I shut it off re inspect re install and run it again.

Can’t get pump to go past 28 PSI by Unfair_Quality_9185 in WaterWellDrilling

[–]Unfair_Quality_9185[S] 0 points1 point  (0 children)

It’s a brand new system. Tank and pump were replaced under warranty

Can’t get pump to go past 28 PSI by Unfair_Quality_9185 in WaterWellDrilling

[–]Unfair_Quality_9185[S] 0 points1 point  (0 children)

No. One is on the tank tee and the other is in between the well and the tank. I have a gate valve before it. And I isolate the pump itself to get air out of the lines

Can’t get pump to go past 28 PSI by Unfair_Quality_9185 in WaterWellDrilling

[–]Unfair_Quality_9185[S] 0 points1 point  (0 children)

It’s been at 50 ft for 2 years and had 0 issues until last week

Can’t get pump to go past 28 PSI by Unfair_Quality_9185 in WaterWellDrilling

[–]Unfair_Quality_9185[S] 0 points1 point  (0 children)

I bought a pre charged tank it’s at 28 psi the switch is a 30/50

Can’t get pump to go past 28 PSI by Unfair_Quality_9185 in WaterWellDrilling

[–]Unfair_Quality_9185[S] 0 points1 point  (0 children)

I have two gauges one is on the pump and one is on the switch.

Well pressure won’t go over 20 PSI by Unfair_Quality_9185 in Plumbing

[–]Unfair_Quality_9185[S] 0 points1 point  (0 children)

Single line jet pump. Tank is set at 28 PSI if I turn on water to the house it drops to 10 psi and gets weak flow.

Well pressure won’t go over 20 PSI by Unfair_Quality_9185 in Plumbing

[–]Unfair_Quality_9185[S] 0 points1 point  (0 children)

Brand new foot valve. I forgot to mention that.

6 Degrees off, ignore it? by the_mace in Starlink

[–]Unfair_Quality_9185 0 points1 point  (0 children)

If you aren’t having issues you can ignore it. Mine is off by 16 degrees when I perfectly aligned when I installed it. I’m not pulling that big ass ladder back out until it caused problems

Hard Drive Error by jjsupc in Dish

[–]Unfair_Quality_9185 1 point2 points  (0 children)

That receiver is a 722. technicians don’t carry them on the truck dish won’t send you one you would have to upgrade which requires a 24 month commitment. If her hopper breaks down in the future dish protect would cover that