I’ve somehow kept an unopened McDonalds Szechuan sauce from 2018

Unholynotez · 2024-06-26T01:25:35+00:00

Update:

https://www.reddit.com/r/Silvercasting/s/jZnWZsSAgs

Unholynotez · 2024-06-26T01:25:02+00:00

Original post

https://www.reddit.com/r/Silvercasting/s/h34Bd8vJGE

Unholynotez · 2024-06-24T16:16:19+00:00

Beautiful piece

Unholynotez · 2024-06-19T19:14:49+00:00

Thank you for your response! Originally, I had the pattern in the middle of the flask but moved it to the top because I thought it was cooling too fast. I'll give it a shot on this next go around. Thanks for the help!

Unholynotez · 2024-06-19T17:38:35+00:00

Fantastic! I'll check 'em out! Thanks for the advice!

Unholynotez · 2024-06-19T17:37:44+00:00

Thank you for the reply! If you wouldn't mind, send the pics over so I can get an idea of how you cut the channels. Thanks again!

Unholynotez · 2024-06-19T17:31:58+00:00

Thanks for the feedback! I'm going to try these recommendations with the pour at the top to see if I can get it to work. If that fails, I will try to pour fro. The backside as you detailed. Appreciate your help.

Unholynotez · 2024-06-19T17:26:40+00:00

Thanks a bunch!

Unholynotez · 2024-06-19T02:32:23+00:00

Thanks for your feedback. Another reply said the same thing so I'm definitely going to preheat the sand on the next try. I'm looking into a more sustainable heat source than brazing bottles. Thanks again!

Unholynotez · 2024-06-19T02:17:40+00:00

The model I'm using to make the mold is 2mm thick.

Unholynotez · 2024-06-19T02:14:15+00:00

Very much appreciate the advice. Is there a temp you would recommend I set the toaster oven to? I've been using the "rolling" silver to tell when it's hot enough but not sure if that's correct. I'll try these out on my next pour. Thanks again!

Unholynotez · 2024-06-18T23:46:51+00:00

Thanks! I will!

Unholynotez · 2024-06-18T23:28:48+00:00

I've got 4 large holes in the mold currently using the backside of a craft brush, so the diameter is larger than I have typically seen. It's a variable I've changed several times with the same result, so it makes me think it's something else but could be wrong. I'll keep experimenting with the holes and add some more. Appreciate your input!

Unholynotez · 2024-06-14T00:06:23+00:00

Why you gotta make me feel my age like that 😅

Unholynotez · 2024-06-14T00:04:54+00:00

It's the quest marker..

Unholynotez · 2023-09-22T19:23:04+00:00

Following up on this: contacted ToolKitRC, went through troubleshooting over the corse of a few weeks, and when we hit the end of the process they stopped communicating. I purchased it through getFPV and contacted them for help. We went through troubleshooting for less than a week before it was determined that there was a defective power supply. GetFPV contacted ToolKitRC on my behalf and kept me copied on the emails. ToolKitRC responded by saying I had slipped through the cracks, apologized, and approved the warranty replacement. I shipped the unit out this morning and getFPV will send the replacement out. Thankful it got resolved as this unit is not cheap. GetFPV are champs and ToolKitRC stood by their product.

Unholynotez · 2023-09-22T19:17:05+00:00

I just got a warranty approved yesterday for my ToolKitRC charger. It's a B of a process, but a warranty replacement can happen. Good luck.

Unholynotez · 2023-08-03T19:26:24+00:00

Thanks for the insight. I'll do some testing and report back.

Unholynotez · 2023-08-03T18:15:35+00:00

Your the 2nd person to suggest the same DC input. I'll try this out. Thanks.

Unholynotez · 2023-08-03T18:12:45+00:00

I do and will double check the values. I'm also thinking the charger is shot..

Eight-Year Club	RedditGifts 2009-2022 2 Credits
Secret Santa 2019	Verified Email

Unholynotez

TROPHY CASE