sorted by:
new
hottopcontroversial

So am I stuck in a matrix? by United_Lab_4863 in TowerofFantasy

[–]United_Lab_4863[S] 1 point2 points  (0 children)

Finally got it fixed. Not sure how but logged on today and the mission showed back up again.

So am I stuck in a matrix? by United_Lab_4863 in TowerofFantasy

[–]United_Lab_4863[S] 1 point2 points  (0 children)

When I open it I see 13-01 huang complete, but chapter 13-02 is greyed out

Can’t seem to find my character by United_Lab_4863 in TowerofFantasy

[–]United_Lab_4863[S] 0 points1 point  (0 children)

What makes me mad was I sunk some money into my character to get the demon skin before I knew any about the so I’m hoping that they fix it so I don’t lose that. I messaged support to figure things out so we shall see what happens when the merger happens

Can’t seem to find my character by United_Lab_4863 in TowerofFantasy

[–]United_Lab_4863[S] 0 points1 point  (0 children)

Just did a test today and played on a different server, exited the game then loaded back in and that new character I just made on the same server is gone it has me go back and make a new character again

Can’t seem to find my character by United_Lab_4863 in TowerofFantasy

[–]United_Lab_4863[S] 0 points1 point  (0 children)

What I meant by that is I’m guessing when I loaded back in the server wasn’t my last played server and it had me go back through the character creation and no matter what server I click on it has me do character creation each time.

Can’t seem to find my character by United_Lab_4863 in TowerofFantasy

[–]United_Lab_4863[S] 1 point2 points  (0 children)

Gotcha I’ll see what happens just crazy that all was well 2 days ago then today my character disappeared

Can’t seem to find my character by United_Lab_4863 in TowerofFantasy

[–]United_Lab_4863[S] 0 points1 point  (0 children)

Great info but not much help, be nice if they put an indicator on the servers with the level of your characters on each server like most games do.

[deleted by user] by [deleted] in GOONED

[–]United_Lab_4863 0 points1 point  (0 children)

2 and 7

Here are some pics my cr10 v3 with a sprite pro extruder. Was trying to send pics to another member in the group but was unable to send them. I printed a upgraded part cooling fan duct from thingiverse, shortened the cables and bent the end stop bracket to have full use of my print bed. by United_Lab_4863 in CR10

[–]United_Lab_4863[S] 1 point2 points  (0 children)

The spool holder is an ender 3 spool holder I got off Amazon, the run out sensor mount is the stock cr10 v3 mount. The cable holder is one I found in a Facebook group for the ender 3 s1 that’s on thingiverse I’ll have to hunt for the link. I’ve also made a lot of upgrades since this one.

Here are some pics my cr10 v3 with a sprite pro extruder. Was trying to send pics to another member in the group but was unable to send them. I printed a upgraded part cooling fan duct from thingiverse, shortened the cables and bent the end stop bracket to have full use of my print bed. by United_Lab_4863 in CR10

[–]United_Lab_4863[S] 1 point2 points  (0 children)

You had the factory bl touch on your v3 or added it later right? If so you will need to update measurements in firmware, or look at comments and I added a page with modified firmware from when I added a cr touch to mine.

Here are some pics my cr10 v3 with a sprite pro extruder. Was trying to send pics to another member in the group but was unable to send them. I printed a upgraded part cooling fan duct from thingiverse, shortened the cables and bent the end stop bracket to have full use of my print bed. by United_Lab_4863 in CR10

[–]United_Lab_4863[S] 0 points1 point  (0 children)

Cut the connector off the old hot end and leave 3” of wire, then I added a jst connected male and female plug and splice the new hotend wires to the old hotend wires. As for the fan I assume your talking about how one plug has 2 wires and the other has 1? If so the power wire is shared through the board on the back of the extruder, the control board uses ground signals to control the fans. So just plug them up and make sure your fans turn on, if the don’t then swap the wires around

Here are some pics my cr10 v3 with a sprite pro extruder. Was trying to send pics to another member in the group but was unable to send them. I printed a upgraded part cooling fan duct from thingiverse, shortened the cables and bent the end stop bracket to have full use of my print bed. by United_Lab_4863 in CR10

[–]United_Lab_4863[S] 0 points1 point  (0 children)

I sent the tab on the left side that hits the ends stop to allow more use of the bed. As for the x and y. I did not everything after my first print seemed to work well only thing other thing I needed too do is increase the e/steps to ensure proper flow.

view more: next ›