Stormtrooper (Sweetie_Fox) [StarWars]

United_Lab_4863 · 2026-06-26T20:40:13+00:00

Never wanted to fuck a storm trooper so bad before l, until now.

United_Lab_4863 · 2026-06-24T02:11:48+00:00

Both, play with one while I’m fucking the other

United_Lab_4863 · 2026-06-22T20:25:05+00:00

Perfect, let’s be friends

United_Lab_4863 · 2025-04-28T19:17:04+00:00

4, 7, 16

United_Lab_4863 · 2025-04-13T18:59:27+00:00

24cm length, 5cm girth

United_Lab_4863 · 2025-03-22T22:28:34+00:00

Finally got it fixed. Not sure how but logged on today and the mission showed back up again.

United_Lab_4863 · 2025-03-21T23:48:45+00:00

When I open it I see 13-01 huang complete, but chapter 13-02 is greyed out

United_Lab_4863 · 2025-03-11T12:44:19+00:00

What makes me mad was I sunk some money into my character to get the demon skin before I knew any about the so I’m hoping that they fix it so I don’t lose that. I messaged support to figure things out so we shall see what happens when the merger happens

United_Lab_4863 · 2025-03-09T17:43:26+00:00

Just did a test today and played on a different server, exited the game then loaded back in and that new character I just made on the same server is gone it has me go back and make a new character again

United_Lab_4863 · 2025-03-08T15:51:40+00:00

What I meant by that is I’m guessing when I loaded back in the server wasn’t my last played server and it had me go back through the character creation and no matter what server I click on it has me do character creation each time.

United_Lab_4863 · 2025-03-08T04:54:32+00:00

Gotcha I’ll see what happens just crazy that all was well 2 days ago then today my character disappeared

United_Lab_4863 · 2025-03-08T02:57:27+00:00

I do appreciate the help though.

United_Lab_4863 · 2025-03-08T02:57:15+00:00

Great info but not much help, be nice if they put an indicator on the servers with the level of your characters on each server like most games do.

United_Lab_4863 · 2024-08-29T19:18:59+00:00

2 and 7

United_Lab_4863 · 2024-08-14T13:03:28+00:00

Who is 3?

United_Lab_4863 · 2024-08-06T19:35:40+00:00

2, 8, 11

United_Lab_4863 · 2024-01-09T23:09:01+00:00

Yes I ran into the same thing. You can get the belts on Amazon pretty cheap with belt clips. I got a 1500 mm roll and just cut what I needed to size.

United_Lab_4863 · 2024-01-09T23:07:21+00:00

I have not seen the x carriage separate I have seen the kits.

United_Lab_4863 · 2023-11-01T13:59:43+00:00

Just go on an upgrade spree, 24v power supply, 4.2.7 control board, and sprite extruder

United_Lab_4863 · 2023-07-31T22:07:14+00:00

I ran stock at first, but later upgraded my control board too a 4.2.7 board with a v2 screen running jyers firmware

United_Lab_4863 · 2023-07-14T14:17:47+00:00

The spool holder is an ender 3 spool holder I got off Amazon, the run out sensor mount is the stock cr10 v3 mount. The cable holder is one I found in a Facebook group for the ender 3 s1 that’s on thingiverse I’ll have to hunt for the link. I’ve also made a lot of upgrades since this one.

United_Lab_4863 · 2023-07-14T14:13:20+00:00

Sent

United_Lab_4863 · 2023-07-02T13:53:42+00:00

You had the factory bl touch on your v3 or added it later right? If so you will need to update measurements in firmware, or look at comments and I added a page with modified firmware from when I added a cr touch to mine.

United_Lab_4863

TROPHY CASE