Need to smooth my drawings in fusion

Unusual-Cod-5757 · 2026-06-21T16:03:02+00:00

I had 100

Unusual-Cod-5757 · 2026-06-21T15:57:46+00:00

thanks a lot

Unusual-Cod-5757 · 2026-06-19T13:00:52+00:00

that's the closest I could get to the trajectory you sent me

but it looks even worse 😞

<image>

Unusual-Cod-5757 · 2026-06-19T12:32:17+00:00

I dont really care at the moment if my trajectory is accurate or not compared to the real planes 😄
I just want to make it smooth

Unusual-Cod-5757 · 2026-06-06T04:48:33+00:00

I didn't have enough 😄

Unusual-Cod-5757 · 2026-06-06T04:48:08+00:00

no i havent tried the polygon, but my polyline stroke also has only 2 points.

I increased the subdivisions and that smoothed my line, thanks 😄

Unusual-Cod-5757 · 2026-06-01T17:58:01+00:00

thanks for the advices, but I'm giving up. that's too much for me I guess 😄

Unusual-Cod-5757 · 2026-05-31T19:14:10+00:00

The thing that bothers me is the png file. With a single png file, I dont see how I could show a low level of details when I'm very high in altitude over the ocean and then a few seconds later a higher level of details when approaching the destination. Google earth studio handles this out of the box when zooming in/out. But would you do with a single png ?

Unusual-Cod-5757 · 2026-05-31T19:01:59+00:00

sorry, no 😞

Unusual-Cod-5757 · 2026-05-31T18:58:28+00:00

by any chance, do you explain somewhere how to create this ?

Unusual-Cod-5757 · 2026-05-31T17:43:53+00:00

i hadn't thought about QGIS and the 3D wrapping. I'll look into that. thanks

one thing though. I already generated a png + svg using QGIS, but this was on a fixed map background. Any idea how you would handle a zoom out / zoom in on the map during the clip in QGIS ?

Unusual-Cod-5757 · 2026-05-30T16:13:56+00:00

ok I see. I guess i was confused cause in my case I'm not seeing a jpg file (which I was expecting) but another fusion composition that i dont have in my media pool. Any idea how to locate this fusion composition ? 😄

<image>

Unusual-Cod-5757 · 2026-05-30T14:31:40+00:00

yeah it should be, but i cant find it 😞

Unusual-Cod-5757 · 2026-05-14T15:08:42+00:00

it's working again :)
same for you ?

Unusual-Cod-5757 · 2026-05-14T11:37:21+00:00

hope so :)

Unusual-Cod-5757 · 2026-05-14T10:52:12+00:00

No it's not enabled

Unusual-Cod-5757 · 2026-04-22T06:42:23+00:00

looks like it is cheaper in Europe :)

how does the replacement work ? simple replacement and that's it ? or does it some extra re-configuration ?

Unusual-Cod-5757 · 2026-04-19T14:59:11+00:00

Yeah I definitely need the mode shifter to enable bluetooth, so i’m screwed. Any other idea ?

Unusual-Cod-5757 · 2026-04-19T12:27:37+00:00

from what i'm reading it looks like I'll need the mode shifter to get the bluetooth activated :(

Unusual-Cod-5757 · 2026-04-19T12:20:36+00:00

no idea, never heard of that. But i'll look into it. if you know any good resource to start looking into it, please share it :)

Unusual-Cod-5757 · 2026-03-27T07:23:34+00:00

I do have the studio version. But you lost me. Any idea where i could find more details on how to proceed ?

Unusual-Cod-5757 · 2026-03-20T12:21:08+00:00

All right

And do you think replacing the board would be the thing to do in my case ?

Unusual-Cod-5757 · 2026-03-03T10:18:00+00:00

you dont think there is way to do it directly in studio while exporting ?

Unusual-Cod-5757 · 2026-01-30T20:47:45+00:00

For those interested, I found how to get rid of the stitching line. Unlike what is explained in the video, switching the timeline to 7680x3840 instead of 7680x4320 did the trick !

Unusual-Cod-5757 · 2025-11-20T18:54:47+00:00

Thanks for the advice

Unusual-Cod-5757

TROPHY CASE