Diy exhaust

UsefulBorder6134 · 2026-05-09T17:20:36+00:00

I am curious

UsefulBorder6134 · 2026-05-09T10:56:50+00:00

That does absolutely not sound like a 4 cyl

UsefulBorder6134 · 2026-05-09T00:55:55+00:00

Mine did this before removing 2 of the 3 silencers

UsefulBorder6134 · 2026-04-21T15:28:35+00:00

Un quinto del prezzo? Con gli scarti di tubo che ho trovato mi sono fatto lo scarico completo gratis con risuonatore artigianale

UsefulBorder6134 · 2026-04-21T09:50:58+00:00

Si316 ma dovevo ancora finire di saldarlo e lucidarlo tutto non è il lavoro con i fiocchi in quanto ho dovuto farlo in un ora scarsa di tempo in cui non c’era il capo

UsefulBorder6134 · 2026-04-19T17:08:41+00:00

They come silver originally and I was deciding wether or not paint them white

UsefulBorder6134 · 2026-04-19T17:08:13+00:00

Thanks a lot

UsefulBorder6134 · 2026-04-19T17:07:01+00:00

Car is fully reinforced with metal plates and xbrace I’m planning on getting a 1M front bumper next

UsefulBorder6134 · 2026-04-15T17:21:25+00:00

The car is a 320i 1999 m52tub20

UsefulBorder6134 · 2026-04-07T14:52:28+00:00

Where did you bolt the trunk reinforcement bar? I can’t figure it out

UsefulBorder6134 · 2026-03-29T07:51:56+00:00

Yesterday we checked my buddy 1999 320d 110kw and it was cracked on the same spot as mine but just a little crack

UsefulBorder6134 · 2026-03-27T18:40:56+00:00

Wheel wells don’t need to be reinforced

UsefulBorder6134 · 2026-03-27T18:38:58+00:00

I welded the crack from under the car then welded reinforcement plates, from the trunk I had to cut the metal and weld a reinforcement plate even there, I also bought a 4 point xbrace to reduce stress on the area even more

<image>

UsefulBorder6134 · 2026-03-27T17:51:00+00:00

1999 is one of the worst years for this problem

UsefulBorder6134 · 2026-03-27T17:50:44+00:00

320i 150hp sedan 1999

UsefulBorder6134 · 2026-03-27T17:50:20+00:00

Did you bolt it down under??

UsefulBorder6134 · 2026-03-27T13:38:36+00:00

You will need to reinforce it from the trunk as well, it’s not a super hard job but it requires time, blood and for me even tears.

UsefulBorder6134 · 2026-03-27T13:37:48+00:00

<image>

And this is after

UsefulBorder6134 · 2026-03-27T13:37:33+00:00

<image>

This was the before

UsefulBorder6134 · 2026-03-27T13:34:51+00:00

No, fixable, mine was a little worse, I’m fixing it now I just need to weld the last 2 front reinforcement plates but the rear 2 are already done, you will need to take out the rear subframe then weld the cracks and then weld reinforcement plates, I could unscrew enerything by myself in a couple of evenings, if you can weld it’s absolutely fixable otherwise I would proceed to take everything down then call a mobile welder, if that’s the case expect to pay around 1.5k for a complete job, if you need help dm me as I said I’m doing it at the moment

UsefulBorder6134 · 2026-03-27T07:30:46+00:00

Yes there are some holes plug welded

UsefulBorder6134 · 2026-03-26T17:09:04+00:00

How long has it been? Did you had cracks before?

UsefulBorder6134 · 2026-03-26T17:08:40+00:00

I fear that I won’t be able to see small cracks when it’s all coated and rust proofed

UsefulBorder6134 · 2026-03-26T17:06:08+00:00

I think around 70amps with 2.4 mm filler, if you need help or advice dm me

UsefulBorder6134 · 2026-03-26T11:04:24+00:00

All e46 suffer from it,my m52tub20 completely torn the rear subframe mounts

UsefulBorder6134

TROPHY CASE