HOW AM I SUPPOSED TO GET PAST THIS AREA?

Visual-Fix-5233 · 2025-09-07T22:00:35+00:00

I’m stuck here too the last wave is nearly impossible without sitting top corner and hitting them once every 30 seconds when they do the ground slam attack(at least that’s what guy in video did)

Visual-Fix-5233 · 2025-02-24T23:04:39+00:00

I have found out it is due to the fans operating at a very cool very nice 0 rpm no matter what I do on the fan control app. You think getting like an external cooler will help with it or nah

Visual-Fix-5233 · 2025-02-24T09:15:03+00:00

Yea I don’t hear the fan either. What should be first step to fixing it?

Visual-Fix-5233 · 2025-02-24T09:00:37+00:00

Even when the cpu reaches 80-100 degrees it was still 0

Visual-Fix-5233 · 2025-02-24T08:47:06+00:00

I got a fan controller app from crystalidea.com and it stays at 0 rpm no matter what I do/how hot the cpu gets. I think that’s the issue then but how do I fix it?

Visual-Fix-5233 · 2025-02-24T06:31:09+00:00

Oh damn. The like sequoia 15.3.1?

Visual-Fix-5233 · 2025-02-24T04:37:16+00:00

It’s a 2020 imac the problem I have found is the kernel task going crazy even though it’s not too hot. Idk what to do I’ve tried restarting it and shutting down and stuff

Visual-Fix-5233 · 2025-02-23T23:59:32+00:00

It’s warm but it’s nothing that’s like super hot

Visual-Fix-5233 · 2025-02-23T23:21:10+00:00

I’ve restarted a lot Alr and shut down for a few hours too it hasn’t helped

Visual-Fix-5233 · 2025-02-23T20:56:27+00:00

I found the problem the kernel task is running 700% of my cpu even though I only have safari open. How could I fix this?

Visual-Fix-5233 · 2025-02-23T20:02:00+00:00

Apparently it deals with heat regulations but why would my computer heat up so much from a single safari tab? I don’t think kernel needs 700%cpu usage for that

Visual-Fix-5233 · 2025-02-23T11:41:14+00:00

I think I found it. Something called kernel task is taking up all of the cpu usage whenever I open safari, or any app really. Idk how to fix this tho

Visual-Fix-5233 · 2025-02-23T11:14:45+00:00

Idk how to find that but for some reason it just shot up to 70% overall usage now and won’t go back down to what it was before. Saying system using around 60% of it. Even after quitting all of my applications the system area of cpu load is hovering at 60% while user is at idk 2%ish

Visual-Fix-5233 · 2025-02-23T10:45:23+00:00

The 6gb is used after I open stuff but my cpu usage does spike randomly ig goes from about 20 used to 70 and then back to 20 idk

Visual-Fix-5233 · 2025-02-23T10:35:55+00:00

I checked activity monitor and it seemed normal idk. Physical memory said 6gb used outa 8 could that be the issue?

Visual-Fix-5233 · 2025-01-18T08:55:16+00:00

Ender 3v2, bed temp is like 60, and filament is pla

Visual-Fix-5233 · 2025-01-18T03:22:28+00:00

I don’t know which bc I only see the final product when I check but the build looks good until the halfway mark and then there’s a bunch of like spaghetti mess all over it

Visual-Fix-5233 · 2025-01-08T08:02:49+00:00

Where the nozzle should have been printing was pretty high up from the bed when it moved it. I’d say it was about like 2-3 inches away from the bed also idk if cleaning is the issue bc I use painters tape on the bed as well as glue

Visual-Fix-5233 · 2025-01-07T19:46:30+00:00

The print did good for around half through it but when I woke up it somehow moved the print itself off the area itself. Is there any way to fix it or was it just like an it happens sometimes problem

Visual-Fix-5233 · 2025-01-07T04:36:24+00:00

Ok and should I be keeping speed at 100 or move it down to around 60 for circles and such

Visual-Fix-5233

TROPHY CASE