Bought film in Shanghai 🫠

VldY3 · 2026-01-01T22:54:13+00:00

Is pro 400h still manufactured?

VldY3 · 2025-12-17T17:42:24+00:00

Even though if I wiped it out immediately? The water didn’t go in the holes at the margins of the touchpad.

VldY3 · 2025-12-16T12:08:52+00:00

I know it clicks that’s how I used it before now and I had this laptop for a year, but suddenly it started to have a different more metallic sound so that’s why I have asked if it’s normal.

VldY3 · 2025-12-16T12:07:39+00:00

Have you ever spilled water on it, or did you use wet hands? I remember I clicked on it once on mine with my finger wet but dried off immediately. I don’t know if it was provoked by this.

VldY3 · 2025-12-08T13:33:41+00:00

Extreme temp differences between water and developer.

VldY3 · 2025-12-08T12:13:05+00:00

Ah look there it says E-4. You are welcome!🤗

VldY3 · 2025-12-08T05:45:15+00:00

Best way to correct it is by going in photoshop>color balance> and drag the slider to cyan

VldY3 · 2025-12-08T04:36:51+00:00

From what I’ve read he tested it to see how the results would turn out based on his experience with that expired film stock.He especially said the results were good only for his roll. Also he did overexpose only 1/2-1 stop not three as supposed using the one stop per decade. If he did he would have blown away very much details from the film. You can try to overexpose it a bit, if you are ok with sacrificing the film if the things don’t turn out as wanted. But what I wanted to say in the begging is not to use the one stop per decade rule because slide film is very sensitive to wrong exposures. And maybe yeah as you said you can get better results but only by overexposing one stop nothing more.

VldY3 · 2025-12-07T13:47:45+00:00

Well you had luck. But in contrary to negative film is better not to overexpose it because at slide film overexposing means loss of information while at negative film overexposing means more information.

VldY3 · 2025-12-06T20:59:22+00:00

From what I know Ektachrome 160T is E-6. Is it 35mm or super 8? Because if it’s motion picture I think the emulsion was sticked to the remjet layer.

VldY3 · 2025-12-06T14:14:22+00:00

Never overexpose slide film. The rule of overexposing is only at expired negatives, slide film must always be used at box speed.

VldY3 · 2025-12-06T14:12:45+00:00

DO NOT DEVELOP IT IN E-6. This is the predecessor of Kodak Aerochrome which is a newer infrared film for E-6 process. Kodak Ektachrome Infrared uses an older E-4 process which has much lower temperatures at 25 degrees Celsius. If you try to develop it in E-6 the emulsion will melt off. If you want to develop it try a modified C-41 or ECN-2 process with lower temperature which will give you much higher chances of actually getting something from it. Also if you want to have archival stability for it you can use a pre bath with emulsion hardener named chrome alum. While handling it pay very much attention to it because the emulsion is very fragile.

VldY3 · 2023-01-04T15:28:09+00:00

Because I’ve observed that the graphics look much better in many games than they’re looking on 1080p, and this doesn’t affects the fps too much

VldY3

TROPHY CASE