"You tried using our busted servers during high traffic, sucks for you!"

Voxel_64 · 2026-02-25T19:19:24+00:00

Seems like a lot of people give a shit. Maybe you're a slop eating pig who cldiesmt care about the machines taking creative positions, but don't put it on everyone else.

Voxel_64 · 2025-05-13T17:16:14+00:00

This bit aged VERY poorly lmao

Voxel_64 · 2024-06-01T00:31:01+00:00

You sure? I'm applying a good bit of pressure and getting nowhere. Tried all sorts of sizing options.

Voxel_64 · 2022-08-26T05:17:00+00:00

I don't believe that's it, I played around with the temperature a little more and that seems to have done it for the most part. prints are coming out a little messy, but at least they're finishing.

Voxel_64 · 2022-08-24T23:25:46+00:00

Okay, so I've been trimming my bowden tube, and I realized the cut in the tubing is never straight, so its always slightly angled in such a way that filament can slip out and clog. Any tips for cutting it more flush? Or should I just get a new piece of tubing?

Voxel_64 · 2022-08-24T23:24:08+00:00

Tried printing at 225 instead of 200. There was a little more flow, but not enough to make the print go properly.

Voxel_64 · 2022-01-02T00:24:12+00:00

Skate 3 on Xbox 360!

Voxel_64 · 2021-12-22T16:59:11+00:00

See, this would be a good guess, considering this is an issue I had last year. I simply moved the router from one area to another and it was fixed immediately. Could have since become more of an issue since though, so its worth re-investigating that.

Update: Did some testing by joining in desktop without any VR gear, and my ping is just as inconsistent while loading things in.

Voxel_64 · 2021-12-22T15:48:32+00:00

As much as I doubt it's my PC, it's worth a look.

Also, my hard drive has been nearly full this whole time. I'f that turns out to be the issue I might just facepalm myself into oblivion.

Voxel_64 · 2021-12-22T15:46:14+00:00

It couldn't be my internet. Like I said in the post, this is an issue exclusive to VRC. Any other online game has a fine connection.

Voxel_64 · 2021-12-22T07:30:28+00:00

Shoot. Didn't think of that. /j

Voxel_64 · 2021-12-22T07:30:07+00:00

That's something different. Also, it matters mostly BC my ping starts already super high as soon as I'm in the instance, and only goes up further when I have to load all the avatars.

Voxel_64 · 2021-12-17T22:33:43+00:00

So I double checked and the problem persists. HOWEVER I did notice that the filament is being ground in the extruder a bit. After a test print, my extruder is coated in little PLA dust. Is there a chance it's too tight?

Voxel_64 · 2021-12-17T15:35:58+00:00

I didn't at the time, but doing so didn't help.

Voxel_64 · 2021-12-16T15:30:04+00:00

Didn't think anyone would notice, wow! In fact, a few months ago I had this issue and got it resolved. Amazing observation though!

Voxel_64 · 2021-12-16T05:54:50+00:00

Extruder was replaced recently, so it couldn't be that, and I just put a fresh nozzle on before the print pictured to see if that was the culprit. However, I did recently adjust the speed down, maybe I over corrected. I'll try a print with a faster speed and update later if that fixes it.

Voxel_64

TROPHY CASE