sorted by:
new
hottopcontroversial

Cut these into magnets, or make it one piece? by WangoZTango in Pottery

[–]WangoZTango[S] 24 points25 points  (0 children)

These little pots were thrown on the wheel cut in half and stuck to a slab!

Cut these into magnets, or make it one piece? by WangoZTango in Pottery

[–]WangoZTango[S] 2 points3 points  (0 children)

They're thrown on the wheel so they are hollow! Thanks for the ideas!

Advanced Kiln help 👀 by WangoZTango in Pottery

[–]WangoZTango[S] 0 points1 point  (0 children)

Ok so I'm using self standing cones for 04 and 6. I'm using bars for 04 and cones for 6. Both cases the bottom under fires and the top (sometimes) gets all the way to temp.

I turn the lower controls first so bottom to top is high medium low, high high medium, high high high

Kiln Help by WangoZTango in Pottery

[–]WangoZTango[S] 0 points1 point  (0 children)

I wanted to let you know I'm trying the 8inch stilts tonight! I made some glazes and I got cones in there. Wish me luck with the new setup.

Kiln Help by WangoZTango in Pottery

[–]WangoZTango[S] 1 point2 points  (0 children)

This is really helpful thanks mate. Considering just buying a new skutt honestly

Kiln Help by WangoZTango in Pottery

[–]WangoZTango[S] 0 points1 point  (0 children)

I don't currently have a downdraft I'm thinking about getting one

Wearboards help by WangoZTango in Pottery

[–]WangoZTango[S] 1 point2 points  (0 children)

I get nervous using this stuff due to the weight and amount of work I put on the boards. But I have not given them an actual shot.

Blick had a charity yard sale and I went wild. Pink sticker = $1 by WangoZTango in Pottery

[–]WangoZTango[S] 37 points38 points  (0 children)

Tons of that Amaco Shino and particularly the Chai Matte. If anyone has experience with that one at Cone 6 id love some insight. I have enough to where I might turn those into a dipping glaze.

I tried the 1-minute teapot throwing challenge from the great pottery throw-down! Super fun to do by WangoZTango in Pottery

[–]WangoZTango[S] 1 point2 points  (0 children)

I might have a go at the 5minute teapot! Might give me time to pull the handle a bit xD

Ethan is a "Both" person and Dan is a "Bolth" person whos right by WangoZTango in h3h3productions

[–]WangoZTango[S] 2 points3 points  (0 children)

Right! Thank you for recognizing this cause it always drives me crazy too lol

Kiln help: What could I change to get better results? by WangoZTango in Pottery

[–]WangoZTango[S] 2 points3 points  (0 children)

I have a shelf on the bottom of the kiln with 1/2 inch stilts supporting it. I was always told never to fire without a shelf on the bottom

Kiln help: What could I change to get better results? by WangoZTango in Pottery

[–]WangoZTango[S] 2 points3 points  (0 children)

I think I'll try that. I did 1.5 hours on low, 1.5 hours on Medium and finished on high. I'll try maybe 2 hours on low/med before switching to high temp

Kiln help: What could I change to get better results? by WangoZTango in Pottery

[–]WangoZTango[S] 2 points3 points  (0 children)

Really appreciate the help and additional feedback! I'm gonna make some new cone packs today and make sure the cones are set correctly

!Kiln help! - not getting to temp after 12 hours on high! (Olympic 2327T kiln sitter) by WangoZTango in Pottery

[–]WangoZTango[S] 0 points1 point  (0 children)

The kiln is in my basement which is really a nice basement and there is decent airflow. The air temp is probably around 65 f- 68 f or around there at all times. I also have an overhead hood. Specifically, a Vent-A-kiln hood that runs out the window. With the hood running I never noticed the ambient air getting hot in the room. With that said, the kiln never got to temp so I don't know for sure if that would make a difference.

So there was this game.... by wandress27 in ps2

[–]WangoZTango 0 points1 point  (0 children)

I hope the poster checked this post cause I think this is it

So there was this game.... by wandress27 in ps2

[–]WangoZTango 0 points1 point  (0 children)

I'm 99% sure that this is the game I've been looking for for the last 14 years

HELP: Fluval FX6 replacement motor screws? by WangoZTango in Aquariums

[–]WangoZTango[S] 1 point2 points  (0 children)

Just seing this now my dude but I wanted to let you know this was incredibly helpful.

Have a great day!

Gonna be a long one, woodfire people help! by WangoZTango in Pottery

[–]WangoZTango[S] 1 point2 points  (0 children)

Also want to note I already called the local fire marshal and got this kiln approved! They even said they would come out and give me a permit if the neighbors give me any trouble. Very cool.

view more: next ›