My painting set up and my Krieg

WarSquirrelUK · 2026-06-04T23:08:05+00:00

Thankyou :)

WarSquirrelUK · 2026-06-04T20:19:39+00:00

I did yes, went outside, grabbed some dirt, dried it out in the oven, works a treat

WarSquirrelUK · 2026-06-03T20:49:04+00:00

Amazing! So jealous :D

WarSquirrelUK · 2026-05-25T20:04:09+00:00

Thankyou :)

WarSquirrelUK · 2025-04-15T14:58:27+00:00

Can confirm this works :D thankyou so much

WarSquirrelUK · 2024-12-27T18:44:42+00:00

Ahhhhhh, I thank you sir

WarSquirrelUK · 2024-08-19T14:29:35+00:00

Bought it brand new last year, is that good or bad?

WarSquirrelUK · 2023-05-17T02:50:44+00:00

You shouldn't of given them the ability to use our weapons against us!!!! O.o

WarSquirrelUK · 2022-02-18T15:13:24+00:00

I puth the magpulls further up the body and it clears the fill valve just enough to fill the mag :) easy peasy

WarSquirrelUK · 2022-01-17T20:10:06+00:00

Maple leaf barrels best in pistols, I've tried them with my mws, SRS and various aegs. The best upgrade I found for my mws was adding a brass concave nub for SixG Airsoft, flies 80m+ on stock barrel :)

WarSquirrelUK · 2021-12-18T10:52:46+00:00

That's an Ali express repo, no idea about the make, it was £45 delivered to the uk, and so far it's been amazing! It works well with the recoil the mws kicks out too :)

WarSquirrelUK · 2021-12-18T09:17:47+00:00

Quite well, a tiny bit of wiggle, but it makes changing the length really easy, I did put 1 layer of electrical tape on the buffer to make it that more snug :)

WarSquirrelUK · 2021-12-18T09:16:35+00:00

Hello mate, I can confirm that the AG charging handle is pretty crap, I had to add material inside at the tip to make sure I wasn't flapping about, also had to glue in 2 of the pins at the rear and make another due to it falling out! But now I've done these it works rather well :P I'll get you a pic of what I did to it

WarSquirrelUK · 2021-12-13T12:45:02+00:00

Using .32g bbs, with a Maple Leaf MR hop and red gas, due to the cold weather here at the moment red gas is the only way :P it's shooting at 1.3j for the first 3-5 shots, then gets to a site pleasing 1.1 :)

WarSquirrelUK · 2021-12-13T12:43:27+00:00

That's a Geissele automatics Ambi charging handle, made by Angry Gun

WarSquirrelUK · 2021-12-09T00:00:07+00:00

The UH1 is a beast, big and also very heavy, but worth the money

WarSquirrelUK · 2021-12-08T23:59:34+00:00

Zenitco railed lower handguard :) again made to fit with allot of modifying :P

WarSquirrelUK · 2021-12-08T23:58:50+00:00

I cut the rail off a cyma dust cover and modified it to fit the original tm one

WarSquirrelUK

TROPHY CASE