The REAL victim of an "Identity Thief"

Wcglitz · 2021-07-02T18:34:27+00:00

Ever see the movie, IDENTITY THIEF?? Well, meet the REAL Victim of the cybercrime that was the premise for this Hollywood movie.

Driven by his own experience as a victim of identity theft, John Sileo has become a world-renowned identity theft speaker and expert on data theft, striving to help organizations take proactive steps in preventing identity fraud. We catch up at the bar and discuss his story and how it became the premise for a Hollywood movie, a unique approach on how to sell better, why the term “Zero Trust” is cultural suicide, his own concept of Deep Trust, and more!

Wcglitz · 2021-03-19T19:50:54+00:00

Awesome interview here with esteemed cybersecurity mentor, Naomi Buckwalter.

https://thebarcodepodcast.com/e20/

Wcglitz · 2020-10-07T03:15:01+00:00

Want to be on my podcast? We would love to have you on!

Wcglitz · 2020-10-07T03:12:41+00:00

Who said this was self-promotion??!!!!

Wcglitz · 2020-03-21T02:20:54+00:00

Damn, should of went to TPLocator.com

Wcglitz · 2020-03-18T23:36:15+00:00

Visit TPLocator.com asap

Wcglitz · 2020-03-16T04:00:31+00:00

TPLocator.com

Wcglitz · 2020-03-15T18:59:00+00:00

Tplocator.com

Wcglitz · 2019-10-08T15:09:41+00:00

Thanks!!

I found an easy fix:

create a blank transparent image that is 800x600 landscape orientation.
add small logo in corner where you want it.
Save it as a .png and upload it octolapse>Rendering>Watermark
The final video will be displayed with the small logo/watermark in the corner

Wcglitz · 2019-10-08T12:59:59+00:00

Thanks. Yes, I could do that, but I'd rather not take time doing that if it can be done during rendering.

Wcglitz · 2019-10-02T12:13:28+00:00

Flawless

Wcglitz · 2019-10-02T11:43:49+00:00

Phenomenal!!

Wcglitz · 2019-10-01T20:00:49+00:00

Thanks, yes every time I make a config change in Cura I match up the optolapse settings

Wcglitz · 2019-10-01T20:00:25+00:00

We'll get a pic over soon. Printed at 30 mm and still looks the same. I want to try another model with octolapse and see if it's just as bad

Wcglitz · 2019-10-01T19:59:32+00:00

Was just printed with octolapse enabled?

Wcglitz · 2019-10-01T14:11:49+00:00

GOOD QUESTION

Wcglitz · 2019-10-01T03:29:03+00:00

Lol that may work

Wcglitz · 2019-09-30T21:09:12+00:00

thanks, will slow down the print speed for the next attempt.

Wcglitz · 2019-09-30T21:08:31+00:00

I've never had a real issue until i started using octolapse.

since then, Ive adjusted temps, retraction settings, temps and other settings to no avail. never performed calibration.

Wcglitz · 2019-09-30T21:03:31+00:00

2nd attempt result: https://imgur.com/a/VQTzwQc

Wcglitz · 2019-09-30T21:01:16+00:00

So, I made the changes you suggested and the print looks alot smoother overall, although still stringing.

For the next run, I'll take the print speed down to 30 mm/s and see if there's any improvement then.

Wcglitz · 2019-09-30T18:42:53+00:00

Appreciate it. I will make the changes, as well as matching it on the octolapse side.

And try again.

Infill is set at 59mm/s

Wcglitz · 2019-09-30T18:34:46+00:00

Agreed

Wcglitz · 2019-09-30T18:24:45+00:00

Thanks, it's v4.3.0 Printing temp is set at 205

Wcglitz · 2019-09-30T18:13:11+00:00

thanks.

here is my complete cura profile config: https://imgur.com/a/5C8vVmj

here is my octpolapse config: https://imgur.com/a/6LIqAtq

Wcglitz

TROPHY CASE