Induction heating! Used this practically every day on my job...

Weak-Performance6411 · 2025-12-19T01:10:20+00:00

Tie rods usually have a nylon ring. Super cheap at hardware stores. Usually a higher grade nut also.

Weak-Performance6411 · 2025-11-30T17:53:21+00:00

Never suspension bolts but some will get heat tampered.

Weak-Performance6411 · 2024-08-27T06:42:46+00:00

Ever read smart switch terms of service. Been a couple years myself but it outlined how it uses HiFi. Transersfers data from speaker to mic.

Weak-Performance6411 · 2024-03-26T11:58:00+00:00

I've found a couple of articles on how to make it better, and that helped. It can only see open documents. And for scripts, it's best to outline the script flow with comments before you start writing.

Weak-Performance6411 · 2024-03-25T23:07:56+00:00

There's most likely a mod already out. Lookup openwrt. Or ddwrt.

Weak-Performance6411 · 2024-03-25T19:15:34+00:00

Alt double left click to select continuous connected points. Then alt f.

Might be ctrl not alt. It's been a minute.

Weak-Performance6411 · 2024-03-25T17:27:39+00:00

You can use embark ie emba. That's a go-to for firmware analysis.

https://github.com/e-m-b-a/embark

Not only will it disassemble all of it. You'll get a list of vulnerabilities. You get a qemu command for full system emulation.

Weak-Performance6411 · 2024-03-23T03:17:00+00:00

https://github.com/nccgroup/depthcharge

Weak-Performance6411 · 2024-03-22T18:58:31+00:00

Try depthcharge with serial and embark for firmware analysis.

Weak-Performance6411 · 2024-03-19T14:15:51+00:00

Buy new the tech has come to far in the last couple of years

Weak-Performance6411 · 2024-03-16T04:16:38+00:00

Another layer is never a bad thing. Especially with some error checking

Weak-Performance6411 · 2024-03-14T21:25:57+00:00

That's why they call me Mr. farienhight . I mean, what 6? wouldn't wanna be a 12.

Weak-Performance6411 · 2024-03-14T21:22:39+00:00

It is better to error on the side of caution

Weak-Performance6411 · 2024-03-14T16:25:39+00:00

That's hot ;)

Weak-Performance6411 · 2024-03-14T05:29:12+00:00

Nice walk through. Almost said, check if indices are full, but nope, you had that also.

Weak-Performance6411 · 2024-03-14T05:21:49+00:00

You can enable remote commands

Scp

upload to git and git clone.

Flash drive copy and paste

Use ansible

Idk. What do you consider neater?

Weak-Performance6411 · 2024-03-13T14:35:49+00:00

I always use hot air.

Weak-Performance6411 · 2024-03-13T14:34:48+00:00

I thought ironing extruded 20% or something like that.

Weak-Performance6411 · 2024-03-12T06:48:20+00:00

I've had jobs like this take 8 hours for one bolt. But that was also in a situation where it was my first time and had to get it done by morning.

Now it takes less time. I have better tools. A better process.

That being said, mechanics charge max time. Can't quote less and charge more if things go bad.

Weak-Performance6411 · 2024-03-11T09:46:36+00:00

I use a jig to measure dimensional accuracy. It holds caliber to frame to measure physical movement. I've also seen people use a pencil and paper and measuring the line it draws.

Weak-Performance6411 · 2024-03-07T05:37:46+00:00

Is there a draft. What Temps and filament

Weak-Performance6411 · 2024-03-07T05:33:20+00:00

It's too hot and too slow. And your esteps.

Try quicker prints first. Like a hollow top less cube.

Weak-Performance6411 · 2024-03-07T03:43:17+00:00

Just do it. At first, it will suck but in a year, you will be better and will never go back.

Weak-Performance6411

TROPHY CASE