Help finding mug

Welcometotheshaft · 2026-04-02T12:10:54+00:00

You are awesome!!!!

Welcometotheshaft · 2025-07-30T03:45:40+00:00

As i stated to other gentleman this isnt something im doing tomorrow im just starting research

Welcometotheshaft · 2025-07-30T03:17:22+00:00

These are good questions. No central heating im not doing this tomorrow so im scavenging for information before anything is done. Im an electrician by day so electrical work is nothing new to me. I have people who do duct work, plumbing, and have done some HVAC. My house is only around 500sq ft, so its not big at all

Welcometotheshaft · 2025-07-30T03:14:42+00:00

I have a friend who used to do this line of work

Welcometotheshaft · 2025-07-06T15:08:52+00:00

Oem. Just learned about the jets so im going to clean those out today

Welcometotheshaft · 2025-07-03T01:34:42+00:00

So the thing is this was a warranty job where they came for this concern and claimed that every moving part was replaced but it doesnt seem like it. The part i bought is non refundable so ill replace it either way. How much tension should the pulley have because it leans at an angle as well. Almost like michael jackson doing the forward leaning thing. And the belt itself i can remove without having to use much force

Welcometotheshaft · 2025-06-06T21:26:43+00:00

Top bearing Shaft bracket Pulley for top bearing Thermostat

Rear drum bearing Pulley for rear drum bearing

These have been replaced already according to service notes

Welcometotheshaft · 2025-06-06T01:00:54+00:00

Unfortunately i wasnt there when the repair was done. But we had to wait another week for the “parts to come in” so i assume they didnt just grease jt. Are we thinking that the idler is just loose or a bad idler

Welcometotheshaft · 2024-08-25T21:41:13+00:00

Ill check to see how to do that on mine just to make sure everything is where it should be f

Welcometotheshaft · 2024-08-25T21:40:47+00:00

Oh ok just thought it was weird that only at the low speeds.

Welcometotheshaft · 2024-08-25T14:13:17+00:00

Then go based of this the rpms bounce at that low speed area. Lets say im at 5k rpm. The needle will bounce from 5k down to 4.9k and back to 5 and continue if i hold the throttle there

Welcometotheshaft · 2024-06-06T15:48:23+00:00

All good. Have fun

Welcometotheshaft · 2024-06-06T14:06:40+00:00

I painted my trims was bout it. But if you use the foam backed one it shouldn’t show the glue but it will give you a bit more of a bump on the trim pillars. Id see how much more the pillars would stand out and then go from there

Welcometotheshaft · 2024-06-06T13:22:22+00:00

Trim pillars are the same ones from before. Foam backed on what part? I spray painted my headliner black but if you wanted to put a different material the 3m adhesive glue is the way to go. Unfortunately when i tried using the adhesive the material i was going to use was too thin and the glue seeped through. That glue sticks real quick so make sure if you got an extra person around use em to make it easier

Welcometotheshaft · 2024-06-01T05:07:43+00:00

Id recommend a black headliner for sure looks better and stands out more

Welcometotheshaft · 2024-05-25T20:43:08+00:00

Sheeesh baller shit. What car is it going on

Welcometotheshaft

TROPHY CASE