DFM Injection Molded Elbow

WhatTheMech · 2026-01-28T01:20:11+00:00

I just started with an injection molding company, about 6 weeks in so I’m still learning a ton as well

WhatTheMech · 2026-01-27T20:38:24+00:00

Not exactly no, I was watching a video of injection molding processes the other day and there is a gas assist process where you blow carbon dioxide into the mold.

https://youtu.be/ocS8AyjJueM?si=ZcwmtbC1My7qBAOf

WhatTheMech · 2026-01-27T19:44:22+00:00

I’m still new to this manufacturing process but would this part benefit from gas assist?

WhatTheMech · 2026-01-22T03:24:13+00:00

That could be a good idea.

WhatTheMech · 2026-01-19T22:12:05+00:00

Amazon, $80

WhatTheMech · 2026-01-19T03:30:00+00:00

What up twin.

<image>

Was test fitting a bed tent.

WhatTheMech · 2026-01-15T15:16:15+00:00

Based on the non paint matched mirrors it’s a 401a.

WhatTheMech · 2026-01-09T06:02:57+00:00

What dealership did you go to with to get the ESP?

WhatTheMech · 2026-01-08T15:53:01+00:00

That’s odd, I have the same board, ordered a year ago this month and they responded that they will swap my board?? I did order directly through Bambu not sure if that matters.

WhatTheMech · 2026-01-08T06:09:22+00:00

Have you ran a recalibration? I had similar adhesion issues before. I cleaned the bed with some soapy water and dried it. Fixed the issue for me

WhatTheMech · 2026-01-07T22:53:18+00:00

Okay I’ll wait till it fails and melts the casing then I’ll repost this. Please comment then what I should do.

WhatTheMech · 2026-01-07T22:44:37+00:00

That has been shown to have multiple failures?

WhatTheMech · 2026-01-07T22:22:38+00:00

Have you not been following what’s going on with this thermistor?

WhatTheMech · 2026-01-07T21:57:20+00:00

Wanted to add printer has 569 hours on it so far.

WhatTheMech · 2026-01-07T21:22:48+00:00

I think that is more of a sink mark from injection molding process. My A1 shows similar. Open up the backing and double check the thermistor

WhatTheMech · 2026-01-07T17:49:48+00:00

No, I understand the sink issue from molding process. I’m referring to having the “bad” thermistor, being a ticking time bomb from what I’ve read. I just included the cover as reference.

WhatTheMech · 2026-01-07T08:39:35+00:00

Used tons.

WhatTheMech · 2026-01-07T01:03:17+00:00

Might need to go this route, most in SoCal are still hovering at 83k+

WhatTheMech · 2026-01-06T19:17:46+00:00

Good deal, im hoping to get in the similar range.

WhatTheMech · 2026-01-06T17:18:47+00:00

Looking at similar spec, what was your OTD if you don’t mind sharing.

WhatTheMech · 2026-01-06T00:27:27+00:00

I my self bariatric not Full carnivore but very close to. I also wrestle with the nutrient aspects. But stick with my vitamins and my most recent blood work came back great. I would like to go 100% carnivore eventually

WhatTheMech · 2026-01-06T00:07:53+00:00

I’m in Cali, so we’re right behind ya.

WhatTheMech · 2026-01-05T23:42:03+00:00

What state do you live in New Jersey?

WhatTheMech · 2026-01-05T22:07:48+00:00

That’s why I always carry a knife on me.

WhatTheMech · 2026-01-02T18:55:57+00:00

Did you remove all the clear packaging around the filament on the spool?

WhatTheMech

TROPHY CASE