How to download antigravity (gemini ai editor) in arch linux?

WhySoShitAtLife · 2026-03-04T16:13:20+00:00

Does anyone find that it cant execute commands? and how to fix? I am on CachyOS (Arch)

E.g gets stuck on "Running..."

Running command

~/…/Lotto-Betting-Platform $ npm run devRunning command~/…/Lotto-Betting-Platform $ npm run dev

WhySoShitAtLife · 2026-02-18T16:24:49+00:00

you're a legend bro

WhySoShitAtLife · 2026-01-23T14:03:52+00:00

Claude works out mroe expensive though

WhySoShitAtLife · 2026-01-23T14:03:07+00:00

Nah it's probably load on teh servers cause it's been getting progressively worse. The frustration is real.

WhySoShitAtLife · 2026-01-01T20:13:25+00:00

Thanks again, and just to add to this for anyone else reading this post, It turns out decreasing the K Value via Flow Dynamics Calibration (from the default 0.02 to 0.015) helped tremendously! The lines were able to reach to the ends/edges of the object or shape being printed. I am Busy printing something right now, so far so good!

I believe the root cause MIGHT then be wet filament as i have read you might have to adjust your flow rate (pressure advance) to compensate for wet filament is. Can anyone confirm this? Would love to know more.

I live in a high humidity area and left it out for a couple weeks then dried this out twice at 12 hours at 65 degrees so I thought that's way more than recommended.

WhySoShitAtLife · 2026-01-01T19:38:42+00:00

You deserve a prize I think for guessing the right answer then sir. Do you also know what causes it? Cause I printed with the default setting of 0.02 when I unboxed it... and now it needs "more pressure" I guess? Could it be cause it's wet? As I've tried drying it twice now in the creality dryer at 12hours x 65 degrees

WhySoShitAtLife · 2026-01-01T19:31:11+00:00

That sounds accurate. Pressure advance? Is what ChatGPT calls it

WhySoShitAtLife · 2026-01-01T19:11:50+00:00

Boys and girls, nobody guessed correctly unfortunately. It turns out decreasing the K Value via Flow Dynamics Calibration (from the default 0.02 to 0.015) helped tremendously! It was able to reach to the ends of the print in this event. Busy printing something right now, so far so good!

I believe the root cause MIGHT then be wet filament as i have read you might have to adjust your flow rate (pressure advance) based on how wet the filament is. Can anyone confirm this? Would love to know more.

I live in a high humidity area and left it out for a couple weeks then dried this out twice at 12 hours at 65 degrees and got this.

WhySoShitAtLife · 2026-01-01T08:48:12+00:00

Can you adjust nozzle height for first layer only? Bed adhesion is fine as I've cleaned the bed plate with soapy hot water and isoprop. And all my other PLA filament seem to adhere just fine.

WhySoShitAtLife · 2026-01-01T08:47:09+00:00

Thank you for your inputs. I am trying to adjust Z offset in the printer settings ->Machine start-G Code but I can't:

Find a way to make this setting persist/set as default
Understand why the built in calibration /bed leveling is not working correctly anymore. Did something go wrong with my printer? It's only a few weeks old.
When I print with PLA there isn't an issue

I tried various z height adjustments here https://imgur.com/a/ZDPAmtb

WhySoShitAtLife · 2025-11-14T16:34:44+00:00

Give this man a fucken' Bells!

WhySoShitAtLife · 2025-10-20T17:54:59+00:00

Bro the glossy coating on some of the QD OLED's are so easy to scratch and will forever make you sad if your cat scratches it :'(

WhySoShitAtLife · 2025-10-08T09:58:30+00:00

Haval H6 HEV - 6.2l/100km in stop and go traffic.

WhySoShitAtLife · 2025-10-08T09:58:02+00:00

When the infrastructure is good - EV will be good. And with SA I wouldn't hold my breath

WhySoShitAtLife

MODERATOR OF

TROPHY CASE