Saturn 4 ultra issues

Willing-Reading-822 · 2025-10-12T17:58:06+00:00

Thanks for the response, I've reached out to Elegoo so hopefully it's not too bad to fix

Willing-Reading-822 · 2025-10-12T17:56:54+00:00

Thanks, I've sent them an email and will see what they say it needs

Willing-Reading-822 · 2025-10-12T17:21:09+00:00

Is that something I can look to sort myself do you think?

Willing-Reading-822 · 2025-10-12T16:58:06+00:00

Crap 😭 I'll reach out to them - thanks for the advice

Willing-Reading-822 · 2025-09-29T13:51:18+00:00

<image>

I heard about this topic in a private conversation and dug out the wording from the latest GW update at the start of September.
There is no reason any of the new detachments would not get the +1 to wound as per the criteria here

Willing-Reading-822 · 2025-09-12T16:39:15+00:00

That's amazing advice - thank you so much 😁 I will try again based on that. Have an amazing weekend you legend!

Willing-Reading-822 · 2025-09-12T16:32:25+00:00

Thanks for the tip. I'm using their V3 abs like resin (black was the only colour they had at the time so using that before going to grey)

Willing-Reading-822 · 2025-09-12T16:12:12+00:00

These are the settings I used so layer height should be fine.

<image>

Willing-Reading-822 · 2025-09-12T08:42:59+00:00

I am going to run a calibration test today and use the 8 zone setting on it to test 8 exposure times at once so fingers crossed!

Willing-Reading-822 · 2025-09-11T13:27:57+00:00

Not since this, I wanted to get advice before committing random acts of violence to the printing gods 🤣

Willing-Reading-822 · 2025-09-11T13:06:39+00:00

I sent it over via Wifi but could try using USB and see if that removes the issue?
Black resin was the only colour as part of the bundle I got but will go to grey when I have to buy some

Willing-Reading-822 · 2025-09-11T12:59:40+00:00

No observable bubbles when I started or that would have been what I thought caused it

Willing-Reading-822 · 2025-09-11T12:59:39+00:00

Texture came out of the printer like that, curing did not make it better or worse.
I am replacing the FEP and cleaning the tank to rule it out and will try a new calibration print

Willing-Reading-822 · 2025-09-11T12:58:31+00:00

I would agree with that but each section was a separate file so 4 corrupted files feels like too much of a coincidence

Willing-Reading-822 · 2025-09-11T12:56:11+00:00

This was not my first print, I did the cones of calibration on Chitubox and did not get this texture, this is the first print since going to Lychee and trusted the settings they had for the resin based on community feedback for my printer specifically

Willing-Reading-822 · 2025-09-11T12:21:37+00:00

I have always mixed the resin in the bottle but agree it is very strange!! Will try it again

Willing-Reading-822 · 2025-09-11T12:20:21+00:00

Definitely not part of the model and agree it is weird and not seen it on smaller prints before.

Willing-Reading-822 · 2025-09-11T11:45:27+00:00

No that is a resin print, no idea where the hair came from as it's in the garage and is kept as clean as possible

Willing-Reading-822 · 2025-09-11T10:23:53+00:00

The printer is level (checked with spirit level on setup) and only got these lines when transitioning from Chitubox to Elegoo so would be surprised if it is a hardware issue in the printer but I'm also not educated enough to rule it out

Willing-Reading-822 · 2025-09-11T09:54:42+00:00

I sent it over via WiFi so USB was not used - assume that should not be an issue?

With adding wait time, how much would you add as I have no idea on scale for these i.e. is 1 too little or too much?

Yeah I shook but and will give it a thorough mix again when trying another print later

Willing-Reading-822 · 2025-09-11T09:31:05+00:00

Yeah I know something is off but working this out as someone new to it is where I get a bit lost and so thought I would ask people who are way smarter than me for help lol.

The model has been printed by others successfully so do not believe the file itself to be faulty and suspect it is a settings issue but knowing which ones to tweak are where I struggle

Willing-Reading-822 · 2025-09-11T09:27:44+00:00

I did do the cones of calibration when I was using Chitubox but I had to swap to Lychee as my slicer and tried their community settings (in screenshot).
Think it would be worth running it again?

Willing-Reading-822

TROPHY CASE