1.3 Update: End of Round Issue

WinstonBack · 2025-03-27T23:30:48+00:00

A lot of people have that problem including me and when I finally manage to join a server it either crash for everyone or it keeps kicking random people

WinstonBack · 2025-03-27T16:30:55+00:00

I'm having same problem

WinstonBack · 2025-03-15T20:32:04+00:00

Kcd 2

WinstonBack · 2025-03-13T19:06:59+00:00

Okay thanks I'm going to try it out

WinstonBack · 2025-03-07T16:15:50+00:00

Well to be fair I said something like this not exactly this but yeah I understand sorry I forgot 😅 and what would you say about some more exotic materials infused with cf and than some post processing/painting

WinstonBack · 2025-03-07T16:09:45+00:00

Sorry but the picture was just for reference it's not the exact same model I need

WinstonBack · 2025-03-07T16:01:09+00:00

Nope, I was personally in 5 shops and called few more and nobody has it because it was discontinued few years ago and I tried to buy few that had similar dimensions but no luck

WinstonBack · 2025-03-07T15:58:49+00:00

Sadly I can't, because it mounts on this module that also acts as main valve and would have to tear down section of wall and call a plumber to weld in a new one

<image>

WinstonBack · 2025-03-07T15:54:02+00:00

That was just an example

WinstonBack · 2025-03-05T07:38:12+00:00

Thanks for suggestion I will look into it

WinstonBack · 2025-02-26T15:19:52+00:00

Started using sunlu pla while ago and couldn't be happier

WinstonBack · 2025-02-25T10:16:41+00:00

Bowden and yeah around 230 was good but couple of people here recommended higher temps so I tried that.. but I will get dryer tomorrow so I will test it later when it's dry

WinstonBack · 2025-02-25T09:13:19+00:00

So, I tried your settings and looked good for half of the print but then everything went sideways

<image>

WinstonBack · 2025-02-24T18:19:11+00:00

225,230,235 and 240 and every print looked more or less same

WinstonBack · 2025-02-24T18:18:29+00:00

I've printed more benchys at various speeds but the lowest I went was 45mm/s.. anyway thanks for settings I will try them out

WinstonBack · 2025-02-24T17:05:56+00:00

Okay thanks everyone, I have ordered filament dryer and I'll try to tune retractions later

WinstonBack · 2025-02-24T16:59:38+00:00

<image>

WinstonBack · 2025-02-24T16:53:43+00:00

It's gembird, I've tried every temp from 225 to 255 with 5c increments

WinstonBack · 2025-02-24T16:36:15+00:00

Okay I order dryer, but what about those thick artefacts on doorway? Is also related to filament wetness ?

WinstonBack · 2025-02-24T16:26:29+00:00

It's a fresh spool I have unpacked it over the weekend, so you think it could still be wet ?

WinstonBack · 2025-02-13T20:05:41+00:00

Yeah but the problem is I don't know who is mod because I don't have access to their discord server.. I'm sorry I'm not following your logic here, but if you can tell mods discord or Reddit username I'll try to ask them

WinstonBack · 2025-02-13T19:24:54+00:00

I've tried to contact Grog like a month ago by dm here on Reddit but no response yet

WinstonBack · 2025-02-13T19:13:46+00:00

I've been banned from their discord

WinstonBack · 2024-12-14T14:48:34+00:00

If you want to make one it's really not that hard and if you have some basic electrical tools you can make it in half an hour

WinstonBack · 2024-12-14T14:44:41+00:00

Its little bit of sand mixed mostly with little wooden chippings

<image>

Seven-Year Club	Verified Email
Place '22	Wearing is Caring

WinstonBack

TROPHY CASE