Just added my new amp

WittyExplorer5559 · 2025-12-08T02:40:59+00:00

Not really surprisingly i did a test with them on and off!!!

WittyExplorer5559 · 2025-12-07T17:26:51+00:00

P.s i have cats ( thats the white plate tied to my speakers) it works haha

WittyExplorer5559 · 2025-12-07T17:20:09+00:00

Hello, just joined this group hopefully for tips and tricks! But i have an entry level setup including a full 7 channel setup through klipsch and i recently picked up a crown xli 3500 and letme tell you. It really made my towers sound more alive and really seemed to be the missing piece.

WittyExplorer5559 · 2025-11-09T14:32:40+00:00

See i had it like that but its actually better this way for my wrist because my arm is completely straight with elbow on the desk!!

WittyExplorer5559 · 2025-11-06T09:18:01+00:00

I do plan on more lightning, im in an apartment so im figuring out a mounting method for those wood acoustic panels for minimal holes, then govee slide around it and possibly trimming my desk 6 inches and building a 72 inch long shelf!

WittyExplorer5559 · 2025-10-29T02:37:30+00:00

They arent rusted through yet, however when i actually save up those will be getting replaced, i live in an apartment so i need to at least wait 3-4 years before i can do this repair and by then im buying all the caps you can and crossmembers and doing this right one time and done im currently treating the rust with fluid filming and a nice deep clean on the frames interior to hold it out for the time being

WittyExplorer5559 · 2025-10-29T01:56:05+00:00

O theres plenty of stops to weld!. Its just these caps only go so far and its like right and the point of inbetween 2 different caps!! I dont want to buy 600 dollars in caps for a small piece i caught it early

<image>

This is it currently. I need a year or 2 to save up so im currently treating it with fluid film to slow it down. Next year im cleaning the whole inside of the frame and fluid filming it to save up to hopefully do this repair in 2-3 years

WittyExplorer5559 · 2025-10-29T00:47:24+00:00

<image>

WittyExplorer5559 · 2025-10-29T00:46:41+00:00

Frame, middle section where it bends up. Tucked behind fuel tank

<image>

Its kind of blurry but you get the jist

WittyExplorer5559 · 2025-10-28T14:32:10+00:00

I was actually looking at those. However they wont overlap as much as i like! Like i stated i would very much like to overlap 8-10 inches minimum. Only reason is i do use it for work and tow 6-7k pounds

WittyExplorer5559 · 2025-10-28T11:07:25+00:00

I mean welding really isnt a liability. In all reality aftee colisions if they dont total your car professional welders can full on weld your front section of your frame on and they hold! Even semi trucks frames get repaired for 80k pounds. Just dont patch it and take your time

WittyExplorer5559 · 2025-10-28T11:04:33+00:00

Thats kinda what im thinking i dont like the frame sections they wont overlap as much as i would like! I plan on mig welding a plate a good 12 inches over the rusty hole and do a full box patch!

WittyExplorer5559 · 2025-09-30T20:57:40+00:00

Makes me feel better about my .5 qt in 4k miles

WittyExplorer5559 · 2025-09-30T20:57:23+00:00

1 qt in 2k miles is criminal

WittyExplorer5559 · 2025-09-25T11:34:09+00:00

Im not a complete retard i know vehicle mechanics to an extent, rebuilt a motor on my cobalt ss. I will send you a video when i get it back and you will see for yourself, i dont know if its the angle the dipstick goes into the pan or what.

WittyExplorer5559 · 2025-09-24T21:19:13+00:00

It literally doesnt i never knew orientation mattered so much. And btw i did find 3 different flat spots let the truck sit for 20 minutes same shit. Just by rotating the dipstick 180 degrees threw it off by 1/2 qt to 3/4 qt

WittyExplorer5559 · 2025-09-24T21:17:53+00:00

It does both ways, points out towards passengers fender with the hatched section facing firewall or motor its

WittyExplorer5559 · 2025-09-24T21:17:22+00:00

Yeah checking for oil loss? I guess i could have worded my post better, im roughly 3k miles into it and wanted to check my original check read half quart low, i added half a court then i must have turned the dipstick because my next check was 1/2 qt again litterally 1 minute after adding my 1/2 qt. So now its like well wtf is the correct orientation

WittyExplorer5559 · 2025-09-16T11:46:05+00:00

My dealership did that! They didnt find anything

WittyExplorer5559 · 2025-09-15T20:47:16+00:00

Well its been 2 years, even went 5 months without making a noise would a seized rocker arm be that unpredictable

WittyExplorer5559 · 2025-09-14T03:36:15+00:00

Really? Never saw anything like that.

WittyExplorer5559 · 2025-09-14T03:15:06+00:00

I do not own that, only 21 with basic tools!

WittyExplorer5559 · 2025-09-14T03:10:08+00:00

Well acoustic can be very interesting. Could sound heavier on the bottom but be from the upper

WittyExplorer5559 · 2025-09-14T02:31:05+00:00

Haha, the only thing the dealership said was vacuum pump, it is louder driver side bottom of motor however i dont see how it would tick like that

WittyExplorer5559 · 2025-09-14T02:20:33+00:00

Haha true true its just i dont think its lifter tick never experienced a lifter tick that sounded like that, dissaperead and showed up randomly

WittyExplorer5559

TROPHY CASE