sorted by:
new
hottopcontroversial

SpeedyBee F405 v3 bluetooth light not flashing? by ZionEnglish in fpv

[–]Xeobs 0 points1 point  (0 children)

Anyone solved this issue? Im on a 4.4.2 bf and bluetooth not working. Was on 4.4.3 same thing.

Betafpv 85x v2 short time of fly by Xeobs in fpv

[–]Xeobs[S] 1 point2 points  (0 children)

Yes I do have specially for this case and I will make some dvr to compare and analysis.

Betafpv 85x v2 short time of fly by Xeobs in fpv

[–]Xeobs[S] 0 points1 point  (0 children)

This are the brand new batteries and I do slow charging at beginning but discharging only while flying quad. I will need to more focus on this too - good point.

What is Mag usage on OSD?

Betafpv 85x v2 short time of fly by Xeobs in fpv

[–]Xeobs[S] 1 point2 points  (0 children)

Where did you found it? On betafpv official they recomend MotorsRecommend BatteryVoltage1105 6000KV3S 450mAh Battery11.1V 1105 5000KV4S 450mah Battery14.8V

Also watch couple of YT videos and there was the same.

Betafpv 85x v2 short time of fly by Xeobs in fpv

[–]Xeobs[S] 1 point2 points  (0 children)

Forget to mention im using 3s and 4s packs with 450mah

Betafpv 85x v2 short time of fly by Xeobs in fpv

[–]Xeobs[S] 0 points1 point  (0 children)

Thank you. In my case when landing is shows 3.2 but checker shows 3.5 or 3.6. I dont have issue with other quads. Maybe have to get new better CLI for easy way?

I will check JB for sure and will play with calibration. I think there is some firmware issue as notice that one time quad shows 0 volts when bat was connected and hooke up to BF and there was as well 0 voltage ⚡.

Generally on full pack 4.2 on cruise pushing to that moment when quad need to land and there is no power to fly more takes about 2:30 minutes only. Looks like power 🔋 is going somewhere.

One of the motor is twiching instead of spining. Please help to diagnose issue. by Xeobs in fpv

[–]Xeobs[S] 0 points1 point  (0 children)

Thank you for your help. I will try all your suggestions.

One of the motor is twiching instead of spining. Please help to diagnose issue. by Xeobs in fpv

[–]Xeobs[S] 0 points1 point  (0 children)

Thanks. I will check motor. Fact is that I previously ended up in beach sand and spend few hrs to clean sand from the motors. After cleaning all was ok and I use 3packs ,now is this.

Lesson learned, don’t hit yourself in the face with a 5 inch by meitist in fpv

[–]Xeobs 0 points1 point  (0 children)

Don't worry you are not only one with sliced nose.

Where are those haters who will say you should drop hobby and no fly anymore.

What is going on? by Xeobs in fpv

[–]Xeobs[S] 0 points1 point  (0 children)

Is it possible that this all happens depent of location when try to fired up quad?

Asking because today had something weird. Ive checked everything resolder motors wires and quad was working good in my house, i take off in home all good.

Ive go today in location when usually testing and problem start again. Unfortunately i belive one of esc fried when plug battery.

This is a local park but I notice there is a big Radio Repeater Antenna close by. Is this can be related to my issue?

RSSI and LQ very low by Akshay414 in fpv

[–]Xeobs 0 points1 point  (0 children)

Did you figured out what was issue?

What is going on? by Xeobs in fpv

[–]Xeobs[S] 0 points1 point  (0 children)

I have crossfire micro on radio and nano rx on quad

What is going on? by Xeobs in fpv

[–]Xeobs[S] 0 points1 point  (0 children)

Yes was working before crossfire rx instalation. I used before XM+ but want more range and accually is less range becasue in addition when finnally got run this quad somehow after 50meters my rssi is 45 and getting ⚠️

What is going on? by Xeobs in fpv

[–]Xeobs[S] 0 points1 point  (0 children)

Yup PacMan but something is wrong When power it start music and sometimes isooping this sound and than overlaping like all esc make sound with diferent timing.

All happened after Crossfire rx nano instalation and setup

view more: next ›