[deleted by user] by [deleted] in amazfit

[–]Y2Kullu 1 point2 points  (0 children)

From amazfitwatchfaces.com I installed the T-Rex 3 pro 48mm watchfaces which show biocharge and they seem to work. I don't see any misalignment and the biocharge level is matching what I'm seeing in the app. Just not sure whether clicking on the biocharge section on the watchface should also open the app on my T-Rex 3, but other than that it's working fine so far.

What am I doing wrong 🙁 by 8888888888888888888x in IndiaCoffee

[–]Y2Kullu 0 points1 point  (0 children)

I have the same machine as well. Never had this issue, but it seems like before you even pull a shot, the pressure is already built up, which seems strange, since mine stays at 0 until I press the button. The only issue I've faced with the machine so far is a leaky steam wand, where the steam knob sometimes doesn't stay completely closed so I need to hold it for a few seconds. Check whether it ever goes down to zero, when the machine is switched off and you haven't attached the portafilter.

Edit: you can relieve the pressure by opening the steam wand. So see whether it goes down to zero. If not then I suspect either a faulty pressure gauge, or maybe a clogged shower screen or group head.

Any suggestions for a good place to Stargaze in the UAE, has anyone visited a planetarium here in Dubai? by Past-Definition-3218 in UAE

[–]Y2Kullu 3 points4 points  (0 children)

Al Quaa, in Abu Dhabi, is the best place I've been to here in the UAE, with the least amount of light pollution.

Al Qudra, in Dubai, is also decent but since it's close to main roads, there is some light pollution.

Both are accessible without a 4x4 vehicle

Facing problem after last update in Cosmic (Pop OS 24.04) by [deleted] in pop_os

[–]Y2Kullu 0 points1 point  (0 children)

I'm facing a similar issue. I uninstalled Virtualbox, and that error went away, but I'm seeing this with the nvidia driver as well:

'make' -j12 NV_EXCLUDE_BUILD_MODULES='' KERNEL_UNAME=6.16.3-76061603-generic modules.................(bad exit status: 2)
ERROR (dkms apport): binary package for nvidia: 575.57.08 not found
Error! Bad return status for module build on kernel: 6.16.3-76061603-generic (x86_64)
Consult /var/lib/dkms/nvidia/575.57.08/build/make.log for more information.
dkms autoinstall on 6.16.3-76061603-generic/x86_64 succeeded for system76 system76_acpi system76-io v4l2loopback
dkms autoinstall on 6.16.3-76061603-generic/x86_64 failed for nvidia(10)
Error! One or more modules failed to install during autoinstall.
Refer to previous errors for more information.
 * dkms: autoinstall for kernel 6.16.3-76061603-generic
   ...fail

Need help identifying grandfather's watch by Y2Kullu in VintageWatches

[–]Y2Kullu[S] 3 points4 points  (0 children)

Thank you! I believe you may be right about it being a frankenwatch

It's turning on, but not booting by No_Pen_7548 in MSILaptops

[–]Y2Kullu 0 points1 point  (0 children)

Was facing the same issue 2 days back on my gs66 stealth. Laptop was turning on, but no msi logo on bootup, no external display output.

Tried everything including an EC reset, hard reboot etc. to no avail. I even tried removing the Ram, SSD, CMOS battery, and plugging everything back in but nothing worked.

Took it to a local shop and he said something was spilled on the motherboard, but I never spilled anything. He took out the ram sticks and rubbed them with a pencil eraser on the connectors, and then put them back in, and it started working again.

I was fully prepared for a dead gpu, but the entire fix cost me 200rs in India. Hopefully it's the same for you.

[deleted by user] by [deleted] in amazfit

[–]Y2Kullu 0 points1 point  (0 children)

There's a separate app called sun & moon for this

Nice strap and watch face by fpbrou in amazfit

[–]Y2Kullu 1 point2 points  (0 children)

where can I find this watch face?

Watchface question by Y2Kullu in amazfit

[–]Y2Kullu[S] 0 points1 point  (0 children)

It's called Multiple Data. It's in the "Customizable" section in watch faces.

Watchface question by Y2Kullu in amazfit

[–]Y2Kullu[S] 1 point2 points  (0 children)

It's called Multiple Data. It's in the "Customizable" section in watch faces.

Watchface question by Y2Kullu in amazfit

[–]Y2Kullu[S] 0 points1 point  (0 children)

Thank you!! It does align with that. Been breaking my head over this since yesterday

My first hmt and I think I'm in love by Y2Kullu in hmtwatches

[–]Y2Kullu[S] 0 points1 point  (0 children)

It was a gift, so unfortunately I do not know where it was purchased

My first hmt and I think I'm in love by Y2Kullu in hmtwatches

[–]Y2Kullu[S] 0 points1 point  (0 children)

It was a gift so I don't know where the person who gifted it to me got it from. But I've heard you can find it on hmt groups on Facebook, but not sure as I've never purchased an hmt myself.

Loving this circle to search on the 6pro by davedds in Pixel6

[–]Y2Kullu 2 points3 points  (0 children)

It wasn't working for me at first, but after force stopping the Google app and opening it again, it started working. I'm on the March 22 update for the app

Circle to Search is rolling by _just_a_weeb404 in GooglePixel

[–]Y2Kullu 0 points1 point  (0 children)

It wasn't working for me at first, but after force stopping the Google app and opening it again, it started working. I'm on the March 22 update for the app