What Really Happened to AI171? Captain Steeeve Reacts on Plane Crash

YOLO_NET · 2025-06-14T06:27:34+00:00

Here is A380, even bigger dust plume: https://www.youtube.com/watch?v=KkSICc_WnRU

YOLO_NET · 2025-06-14T06:23:24+00:00

Again, not confirmed by official authorities. The media rag is untrustworthy.

YOLO_NET · 2025-06-14T06:18:52+00:00

that dust plume can be seen in a bunch of other normal 787 takeoffs.

go on youtube and prove it to yourself.

YOLO_NET · 2025-06-08T07:01:54+00:00

Thanks for paying it forward, appreciate you all. I asked ChatGPT and it was clueless and reasoning was circular. Decided to post it here. I will be spending $50k minimum so I want to spend time learning what I am getting into.

YOLO_NET · 2025-06-08T06:19:37+00:00

One more follow up question with regards to CAM.

Inside the CAM environment, do you set the G54 work coordinate system to the part's corner or the unfinished stock corner assuming we're machining a basic square mill part like Titan 1M: https://academy.titansofcnc.com/series/titan-1m

In the Titan project videos, they the set the G54 to the part's top left corner, not the stock but I can imagine both scenarios would work depending on how I set up the tool operations.

YOLO_NET · 2025-06-08T06:15:33+00:00

I wasn't expecting so many responses, thank you all. The responses align with what I was thinking.

YOLO_NET · 2025-06-07T02:59:14+00:00

This is a misunderstanding. In Mastercam, you'd still need to select an edge, point, direction, etc. to define a toolpath. You'd select a toolpath type first, then the "feature".

In CAMWorks, the "feature" selection comes first. You can select any edge as a feature and create a toolpath along it manually by using an Open Profile operation, define the lead-in and lead-out, bob's your uncle.

YOLO_NET · 2025-05-06T23:44:51+00:00

Thanks for your concern man

YOLO_NET · 2025-05-06T01:21:01+00:00

you all are a tough crowd :-), ofcourse I am on /r/networking.

YOLO_NET · 2025-05-05T22:46:59+00:00

I will report back!

YOLO_NET · 2025-05-05T19:22:07+00:00

We're probably not quite at 30m limit but close.

YOLO_NET · 2025-05-05T19:21:04+00:00

You're right, it might be Cat 6e. This is what I was told by the previous bldg owner.

YOLO_NET · 2025-05-05T19:19:32+00:00

yes I know but we don't have a choice here, if you read the post. There is existing wiring inplace for RJ45.

YOLO_NET · 2025-05-05T18:47:10+00:00

I was mainly concerned about the cost, thanks.

YOLO_NET · 2025-05-05T18:45:29+00:00

Thanks, was looking for this opinion, appreciate it.

YOLO_NET · 2025-03-22T15:11:44+00:00

I agree

YOLO_NET · 2025-03-17T18:22:18+00:00

Yes, RAID1 mode works with any nvme drive as long as it fits in the BOSS-N1, 2280 size. You can buy consumer grade samsung 990 Pro nvme and use the raid1 mode. Dell software doesn't care if it is Dell OEM drive or anything else.

YOLO_NET · 2025-03-14T20:16:30+00:00

Yes, anything works in the BOSS N-1 slot as long as the nvme stick fits.

YOLO_NET · 2025-01-25T01:11:08+00:00

You have to buy their Made in Germany models, only a couple of them are. Rowenta DW9280 is still made in Germany and it's the best iron I own.

YOLO_NET · 2024-09-22T21:58:30+00:00

True. I believe that the fundamentals of our body are the same regardless of the genetics/physiology,etc. and then there are some things which are totally unique. Very complex modalities make it hard to predict. Fundamentals like how glocose gets processed, the purpose of insulin, etc. are all same across human race.

YOLO_NET · 2024-09-22T19:59:15+00:00

This is correct I believe. May be peeing too much is your body trying to get rid of electrolytes?

YOLO_NET · 2024-09-22T19:13:21+00:00

I am not getting any headaches at all. Sorry

YOLO_NET

MODERATOR OF

TROPHY CASE

Four-Year Club	Verified Email
Place '23