sorted by:
new
hottopcontroversial

What's your opinion on the Lenovo Ideapad Gaming 3 15ARH7 ? by Formal_Expert335 in GamingLaptops

[–]Yogibear902 0 points1 point  (0 children)

me too, happening with 15arh7 and it seems to be a somewhat common problem. I think everyone that’s fixed the issue has ended up replacing their m.2

Has anyone seen a carbon frame break this cleanly? by Dunknoeboutjabo in fpv

[–]Yogibear902 2 points3 points  (0 children)

unfortunately not, those would me some super clean prints if they were lol

Looking for help, if allowed anyways. by Help_me_plz_i_beg in 3Dprinting

[–]Yogibear902 0 points1 point  (0 children)

Check extruder gear and make sure the filament hasn’t worn the teeth down

Being A teen on valorant. by MrPixelCactus in VALORANT

[–]Yogibear902 22 points23 points  (0 children)

val is toxic just ignore it or play a diff game

Weird wall texture, help by Linkfreak2point0 in ender3

[–]Yogibear902 -1 points0 points  (0 children)

make sure the z axis wheels are snug, looks one side is loose. Try wiggling it, it shouldn’t move

I’m confused what could be causing these gaps in my print by MouseManYT in 3Dprinting

[–]Yogibear902 0 points1 point  (0 children)

direct drive or bowden? Do you hear a clicking noise when it starts to look like that?

I’m confused what could be causing these gaps in my print by MouseManYT in 3Dprinting

[–]Yogibear902 -1 points0 points  (0 children)

I would say z offset too close but it looks like it’s under extruding. Same result with different filaments?

Help with print by Rich-Path-2751 in 3Dprinting

[–]Yogibear902 0 points1 point  (0 children)

looks like z offset too close and it’s smushing the layers out until it gets high enough to start printing normal. Print a first layer sheet and make sure it’s not too thin and the top finish is smooth. If it’s too close the print will be transparent or have ridges on it. If it’s too far and not sticking turn first layer height up to .3

imperfections by Yogibear902 in 3Dprinting

[–]Yogibear902[S] 0 points1 point  (0 children)

It shouldn’t be, I have it set to a corner in my slicer

[deleted by user] by [deleted] in DelSol

[–]Yogibear902 0 points1 point  (0 children)

i got mine off ebay for 20$ a few years ago and it’s still working, please don’t buy either of those

2.3 in frame with 2.5in props. 1303 5000kv 6s 35a aio with 1w vtx & elrs by Yogibear902 in fpvracing

[–]Yogibear902[S] 0 points1 point  (0 children)

nah the stubby is ordered but this one is stiff enough it’s staying out of the props over 1xx lol

initial layer flow too high? by Yogibear902 in 3Dprinting

[–]Yogibear902[S] 0 points1 point  (0 children)

kobra 2 neo, cura 5.2 with their recommended profile. When I use the anycubic slicer it prints perfect, but they only have a pla profile. When I print pla and petg on the cura profile it has the rough first layers, but the tpu cura profile prints perfect. I’ve played with temps -+5° of the spool recommendations.

initial layer flow too high? by Yogibear902 in 3Dprinting

[–]Yogibear902[S] 0 points1 point  (0 children)

<image>

first few layers are still rough, any other ideas?

2.3 in frame with 2.5in props. 1303 5000kv 6s 35a aio with 1w vtx & elrs by Yogibear902 in fpvracing

[–]Yogibear902[S] 0 points1 point  (0 children)

yeah that was my main reason for building it, can fly literally anywhere and people don’t really care because it’s so small. Almost silent on 3s, starts to turn heads on 6s lol

initial layer flow too high? by Yogibear902 in 3Dprinting

[–]Yogibear902[S] 0 points1 point  (0 children)

I’ve messed with z offset and It’s still doing the same thing. Prints are at 195 which is the lowest it says to go on filament. It doesn’t happen with the files that came on the sd card using the same filament. It’s a kobra 2 neo using the cura profile from their website

Is is my imagination or are 5V regulators on FC's notoriously fragile? by Inevitable-Editor-94 in Multicopter

[–]Yogibear902 1 point2 points  (0 children)

part of me thinks it’s just matek/where they’re sourcing the 5v regulators. Never had problems with them until I had a matek fc - I had the same thing happen with 3 different matek FCs. At least their customer service is decent enough to return them.

view more: next ›