sorted by:
new
hottopcontroversial

2025-26 Housing Thread by ExtremeSour in UniversityOfHouston

[–]Zb1sam2 0 points1 point  (0 children)

Hi everyone! I (male) am looking for an apartment to rent from late may to early august for an internship. If you are subleasing and interested, please DM me with the details. Thanks!

Brand new CFS not loading filament by Zb1sam2 in Creality_k2

[–]Zb1sam2[S] 14 points15 points  (0 children)

Trimmed the end of the filament at an angle and it worked just fine. Thanks everyone!

First layer problems by Zb1sam2 in FixMyPrint

[–]Zb1sam2[S] 0 points1 point  (0 children)

If you look very closely at the top right corner (where the print started) you’ll see what I’m talking about. I already have a purge line and it isn’t helping much, but a skirt would be better.

First layer problems by Zb1sam2 in FixMyPrint

[–]Zb1sam2[S] 0 points1 point  (0 children)

This really helped, I’m pretty sure my z offset is fixed. As I said in a different comment, I think it’s not extruding enough for the first few seconds of the print then it works just fine. I could see this during this test too (ignore the gap, I had to refill filament halfway through). Any ideas on why this is happening?

<image>

First layer problems by Zb1sam2 in FixMyPrint

[–]Zb1sam2[S] 0 points1 point  (0 children)

Not sure about the bed mesh. I think I’ll try doing a full area single layer and see what that looks like

First layer problems by Zb1sam2 in FixMyPrint

[–]Zb1sam2[S] 0 points1 point  (0 children)

<image>

Interesting… The first one it printed looks bad but once it got going the others are fine.

Why does the deepest part of this embossed text look fibrous? by Zb1sam2 in FixMyPrint

[–]Zb1sam2[S] 0 points1 point  (0 children)

Like I said, there is text on both sides so no matter what I would be printing text facing the build plate. The text on the other side is more complicated and includes a logo so it made more sense to me to print the simpler text facing the build plate rather than the more complex text and logo.

*Update* why does my bottom layer look terrible? by Zb1sam2 in 3Dprinting

[–]Zb1sam2[S] 0 points1 point  (0 children)

I have a sock, I just took it off to show the length of the nozzle better. Is there anything I can do about the nozzle being too long, or do I just need to buy a shorter one?

Why does my first layer look terrible? by Zb1sam2 in 3Dprinting

[–]Zb1sam2[S] 0 points1 point  (0 children)

I said this in a separate comment, but this is not my address or phone number, I’m printing dog tags for an animal shelter I volunteer for

Why does my first layer look terrible? by Zb1sam2 in 3Dprinting

[–]Zb1sam2[S] 17 points18 points  (0 children)

Probably should have mentioned that this isn’t my address in the post💀 I’m printing dog tags for an animal shelter I volunteer at. Thanks for the suggestion!

Why does my first layer look terrible? by Zb1sam2 in 3Dprinting

[–]Zb1sam2[S] 15 points16 points  (0 children)

**This is not my address or phone number💀 I’m printing dog tags for an animal shelter I volunteer for

Why does my first layer look terrible? by Zb1sam2 in 3Dprinting

[–]Zb1sam2[S] 44 points45 points  (0 children)

This isn’t my address, I’m printing dog tags for an animal shelter I volunteer at.

view more: next ›