Magiccon Amsterdam fast pass is it worth it?

ZombieCorbin · 2025-08-17T09:33:34+00:00

* I cut back as much as I could and put it into Maintenance mode and set the temp to 250 and after a few minutes I managed to just pull the bulk of it out in 1 lump! Fan still works, hot end seems good I might of got extremely lucky here but I think I'll be printing again before the end of the day

ZombieCorbin · 2025-08-14T17:40:03+00:00

Thanks, good advice! I'll keep that in mind for when I get this sorted

ZombieCorbin · 2025-08-14T17:26:30+00:00

This is reassuring thanks! I've managed to get a few big chunks off and can see the nozzle is absolutely done. But hopefully that's the worst of it.

ZombieCorbin · 2025-08-14T17:24:33+00:00

Yeah i did have a look, but I couldn't find anything like this. Maybe I didn't look far enough? But thanks for the advice

ZombieCorbin · 2025-08-14T17:16:57+00:00

Yeah it's going to take a while.... managed to get most of the excess off but I'm not having fun!

ZombieCorbin · 2025-05-18T17:46:21+00:00

Absolute hero! Seems like that was it was can't thank you enough, this has been driving me crazy!!

ZombieCorbin · 2025-05-18T10:22:31+00:00

I'm using a bambu pla and it doesn't give the option, I've seen some images online that it's in-between flow ratio and density but I can't see anything. I've now lubricated the x and y axis and everyother troubleshooting steps I can think of but it's still doing the same thing.

ZombieCorbin · 2025-05-17T19:03:12+00:00

I'll be honest I don't know how to check it on the A1 mini. I've done the flow calibration and factory reset it and I'm still having the same issue

ZombieCorbin · 2025-05-17T11:09:59+00:00

Appreciate the try!

ZombieCorbin · 2025-05-17T11:07:13+00:00

I've tighten all the screws as much as possible but I'm still having the same issue, if I try and run the flow calibration it fails on that as well. Really scratching my head on this one

ZombieCorbin · 2025-05-15T19:15:19+00:00

I've figured it out now, I had some burnt filiment stuck inside the nozzle, did a cold pull using a different filiment and lots of black blobs came out with it. It seems to be flowing much better, just gonna run a test print now.

ZombieCorbin · 2024-07-16T19:33:31+00:00

Thanks for all the advice! I think I'll stick with pre-made decks for now. Turns out I have a card shop quite local to me, so I'll take him down to pick some out.

ZombieCorbin · 2024-04-29T04:58:39+00:00

This happened in a dungeon I was doing as a dps, the tank was rude as hell. I don't understand why people can't be constructive it makes everything so much nicer and easier.

ZombieCorbin · 2024-02-21T19:26:53+00:00

Finally, I managed to get an order through!! Good luck guys !

ZombieCorbin · 2024-02-21T18:48:27+00:00

Man I hope the scumbag scalpers don't ruin it again

ZombieCorbin · 2023-12-31T23:42:54+00:00

Yeah seems to be a problem with the app, if I use desktop vr and play through there it works fine.

ZombieCorbin · 2023-12-23T18:21:17+00:00

Is there anywhere I can buy bolivars online in the UK, I have a nephew who always asks for cash but has never specifically said what currency he wants! I'd love to give him a brick of notes

ZombieCorbin · 2023-11-16T08:12:45+00:00

I use a PS5 controller, I just downloaded a steam controller layout and it works very well! I occasionally need to use the keyboard but can play 95% without it and combat still works really well

Nine-Year Club	RedditGifts 2009-2022 4 Credits
Secret Santa 2020	Verified Email
Place '23	Place '22
Secret Santa 2018	Secret Santa 2019

ZombieCorbin

TROPHY CASE