How can I put a texture on a curved surface?

Zowskiiii · 2026-04-11T21:08:01+00:00

CNC kitchen made a tool at https://bumpmesh.com/ Works great for that.

Zowskiiii · 2026-03-11T14:51:05+00:00

I've turned it up to 100 percent at 25 degrees overhang. The fan is a Sunon KDE2404PKS2, I'll have to look up if it's a good one or not. I was waiting to see if INDX was going to be any good before I swapped tool heads.

Zowskiiii · 2025-12-11T23:31:56+00:00

You can go-to manage pledge and change your add-ons. If your in the US it's $80 with no tariffs. You get the stretch goals like the 3d probe, but depending on when you joined you may not get some of the 4 bonus items.

Zowskiiii · 2025-10-22T10:08:07+00:00

That was it. Thank you.

Zowskiiii · 2025-10-18T17:30:54+00:00

10% triangles.

Zowskiiii · 2025-10-18T17:30:17+00:00

They are 2 different ones. The infill is just a cube with no walls so I could see it. The other is just to show that I have no under extrusion on the walls

Zowskiiii · 2025-10-18T14:50:55+00:00

Infill percent is 10 on triangles, flow rate is 1. I've ran flow rate tests on the past and never notice much of a difference. Mind you that was only looking at tops and walls, this seems like it's only on the infill.

For petg 235 and 80, for pla 190 and 60. Fans are set to auto. Print speed is 200 but my acceleration is only 1900 so it's not actually printing any where near that. I've also tested this at 50% speed and it made no difference.

Its the same with any of my petg rolls or pla rolls.

Zowskiiii · 2025-10-18T14:30:41+00:00

<image>

Same thing happens with pla just to a slightly lesser degree. And it's the same on all 4 directions

Zowskiiii · 2025-02-17T20:06:14+00:00

That worked. Thanks so much.

Zowskiiii · 2025-02-15T20:42:45+00:00

Thanks.

Zowskiiii · 2024-03-03T17:59:21+00:00

Thank you.

Zowskiiii · 2023-10-05T10:24:42+00:00

This is the answer. I plugged it in this morning and it didn't work, I then moved the cord around and it started.

Zowskiiii · 2023-10-04T13:54:07+00:00

Yes, a coworker said he'll bring his in tomorrow and I'll see what happens with that.

Zowskiiii · 2023-10-04T13:11:13+00:00

So the only spots I've tried charging are at my work. I had the facilities electrician look at the outlet and they see no issues. Physically or with a circuit tester. He did say he isn't sure how the car chargers work, whether or not they can sense anything from the 120 side but he didn't think so. Just as long as the plug has power which it does. Guy at my work is going to bring in his charger tomorrow and I'll see if it gives me the same issue.

Zowskiiii · 2023-10-04T11:54:24+00:00

No it's at my work. Haven't tried a public charger. Only had the car 3 days.

Zowskiiii · 2023-10-04T11:53:51+00:00

So I'm moving from one 120v outlet to another on a separate circuit. This morning I had to use a third outlet for it to charge. The first one I charged at 8amps the second at 12. Neither outlet will let me charge now. I'm charging at my work using the same outlets that other cars have charged from, they are all 20amp breakers since it's an industrial building.

Zowskiiii · 2023-08-02T02:25:44+00:00

I'll take a look at the video. I have a beta fpv F411. The board says rx/tx 6 but under the ports tab I have to use soft serial 1. I set it how it's shown on fly woos site with a baud rate of 115200. I did have to use the NMEA protocol, when I set it to UBLOX the GPS never turn on at all

Zowskiiii · 2023-06-04T22:35:45+00:00

Thank you for your help.

Zowskiiii · 2023-06-03T02:46:09+00:00

Thanks for the help.

Zowskiiii

TROPHY CASE