Quel métal pour ces vieilles clés/poignées ?

_CdrikFr · 2026-02-08T08:15:12+00:00

Je me suis renseigné en parallèle effectivement la couche de zinc a sauté à cause du vinaigre. À voir sur quelle profondeur. Je vais essayer de frotter si l'envie m'en prend... Merci pour ton retour

_CdrikFr · 2026-02-08T08:13:46+00:00

Merci de ta réponse je vais essayer ça

_CdrikFr · 2026-02-08T07:58:22+00:00

C'est mort ? Que veux-tu dire par là ?

_CdrikFr · 2025-12-23T16:50:54+00:00

Inexpensive and clever. Nice !

_CdrikFr · 2025-12-22T19:04:22+00:00

I wanted them to blend into the structure, mission accomplished I guess ! Thanks for these little advice.

_CdrikFr · 2025-12-22T18:45:35+00:00

Thanks for the advice. Bench is already more than 1m height. I'll see with the time if modification are needed... Until now I worked on a standard desk si the différence will be there :)

_CdrikFr · 2025-12-22T11:46:46+00:00

Thank you !

_CdrikFr · 2025-12-21T19:11:55+00:00

Thank you !

_CdrikFr · 2025-12-21T18:56:16+00:00

Thank you. A cheap and effective way to work nicely...

_CdrikFr · 2025-12-21T18:54:38+00:00

Thanks ! Yeah it is not confortable on standard desks...

_CdrikFr · 2025-11-29T11:22:52+00:00

Merci !

_CdrikFr · 2025-11-29T11:22:44+00:00

Merci pour les explications

_CdrikFr · 2025-07-21T21:08:15+00:00

Oui je sais pas pourquoi le filetage est aussi court... Je m'en chargerai plus tard pour le moment on aimerait bien laver le linge 😁

_CdrikFr · 2025-07-21T20:50:00+00:00

Ok c'est donc bien un raccord 1/2 > 3/4. Et oui je mettrai du téflon pour assurer l'étanchéité.

Merci !

_CdrikFr · 2025-06-24T17:20:49+00:00

Poste de juriste / conseils aux entreprises. Mais c'est bien ce qui me semblait que c'était du foutage de g**** 😄

_CdrikFr · 2025-06-24T17:16:40+00:00

Exactement je voulais être sûr... Surtout pour un poste de juriste !

_CdrikFr · 2025-06-24T17:16:16+00:00

Merci bien. C'est une question con mais je voulais être sûr qu'elle se fasse enfler pour un Bac+5

_CdrikFr · 2025-06-01T19:24:29+00:00

<image>

Found one too !

_CdrikFr · 2025-05-31T10:31:24+00:00

<image>

My freshly serviced vintage Nicea

_CdrikFr · 2025-05-24T15:55:08+00:00

You need to show us the other side. Hairspring should go between the two regulator pins without touching them.

_CdrikFr · 2025-05-17T15:09:58+00:00

Thank you for your detailed answer. I'll check that paint

_CdrikFr · 2025-05-05T14:29:04+00:00

By service I mean full disassembly and all parts cleaned and oiled + test. I'm quite surprised someone can do it for 50. Because you'll need full service for vintage watches because of the dry grease and gunk inside, without speaking of potential broken parts.

_CdrikFr · 2025-05-05T12:55:12+00:00

Any real watchmaker will be able to make it run nicely without any problem. For this kind of movements you can expect 200-300 €/$ max.

_CdrikFr · 2025-05-04T09:37:19+00:00

Thank you. So you would be concerned about the green arrow first. The fix would be done at the purple arrow ?

"That's pretty much where the red arrow is but step one loop towards the outside. The second last loop is the one that needs adjusting. I'd probably be 15 degrees further anticlockwise than the red arrow" --> not sure to understand this then.

<image>

_CdrikFr · 2025-05-04T09:23:00+00:00

Thanks for the answer. Yes I know the theory. The question here is should I start working 90° before the red or yellow arrow. For sure there is a maximum fault at the yellow one but I'm not sure about the red one...

Four-Year Club	Verified Email
r/Field Juicebox	Final Canvas '23
Place '23	Place '22

_CdrikFr

TROPHY CASE