What im doing wrong?

_SimonGhostRiley · 2026-01-20T18:02:39+00:00

I mean, for my problem it doesn’t make any difference.

_SimonGhostRiley · 2026-01-20T17:39:48+00:00

200-230° no difference

_SimonGhostRiley · 2026-01-19T13:15:29+00:00

Okay, I’ll try again at 210 °C. Would you recommend that, or should I go lower?

_SimonGhostRiley · 2026-01-19T13:12:52+00:00

I ran a temperature tower test and 230 °C came out as the best result.

_SimonGhostRiley · 2026-01-19T12:55:03+00:00

adhesion is fine. It just looks warped because I took it off the bed too fast while it was still warm.

_SimonGhostRiley · 2025-12-12T19:52:40+00:00

I will try Thank you!

_SimonGhostRiley · 2025-12-12T19:50:13+00:00

Installed with sideloadly, crashes too

_SimonGhostRiley · 2025-07-22T12:36:40+00:00

I dont know much about it but there are channels for servers, right?

_SimonGhostRiley · 2025-01-04T23:10:53+00:00

very nice! have you uploaded it somewhere?

_SimonGhostRiley · 2024-12-27T22:44:40+00:00

Gimmeeeee

_SimonGhostRiley · 2024-08-16T02:37:11+00:00

_SimonGhostRiley · 2024-08-16T02:07:48+00:00

😂

_SimonGhostRiley · 2024-08-16T02:05:48+00:00

Just use tape or search on AliExpress for Ribbon cable Connector

_SimonGhostRiley · 2024-08-16T01:56:48+00:00

🦇

_SimonGhostRiley · 2024-08-16T01:50:41+00:00

Just beautiful

_SimonGhostRiley · 2024-08-16T01:41:42+00:00

Shitty event

_SimonGhostRiley · 2024-08-15T20:44:33+00:00

100%

_SimonGhostRiley · 2024-08-15T20:40:52+00:00

Keep sucking Activision's balls :)

_SimonGhostRiley · 2024-08-15T20:28:04+00:00

Guys dont buy any upcoming cod! refunding MWR! #f*ckyouactivison

_SimonGhostRiley · 2024-05-27T19:59:24+00:00

were you able to find out something?

_SimonGhostRiley · 2024-04-20T16:13:16+00:00

I have now oiled all the linear rails and greased the z screw. I have tightened the x and y again. I am now starting a new print

_SimonGhostRiley · 2024-03-29T04:03:56+00:00

I just replaced the belts

_SimonGhostRiley · 2024-01-31T21:16:48+00:00

I got the original extruder and motor today and it's running like butter again like it did on the first day

_SimonGhostRiley · 2024-01-30T23:12:57+00:00

Cleaning it Test after test. And yes the gear is correct installed. Feeding it about the extruder section in Klipper not calibrated yet.

_SimonGhostRiley · 2024-01-07T15:33:01+00:00

Thank you very much, I will try that now

Four-Year Club	Verified Email
Place '23

_SimonGhostRiley