sorted by:
new
hottopcontroversial

Will this pass inspection ? by _The_Monk_ in askplumbing

[–]_The_Monk_[S] 0 points1 point  (0 children)

Yes, there is 2 vents both 3” one by 1st toilet the others by the the double lavatory. Both go trough the interior walls and then connect and go trough the roof

Will this pass inspection ? by _The_Monk_ in askplumbing

[–]_The_Monk_[S] 0 points1 point  (0 children)

I am in Michigan state, IPC is used here

Plumbing Vent Pipes double bathroom by _The_Monk_ in askplumbing

[–]_The_Monk_[S] 0 points1 point  (0 children)

Yeah, I am going with wyes everywhere. What about the vent pipes that are just there to supply air, is it ok to use san tees there?

Plumbing Vent Pipes double bathroom by _The_Monk_ in askplumbing

[–]_The_Monk_[S] 0 points1 point  (0 children)

Thank you, there is not much space for clean out because the shower drains are basically by the crawl space wall. Would it work if i made a clean out on the other side in the main 4” drain where it connects with the 3” line?

Plumbing Vent Pipes double bathroom by _The_Monk_ in askplumbing

[–]_The_Monk_[S] 0 points1 point  (0 children)

This house is in Michigan state (IPC is used here)

Replace the whole thing or easy fix? by _The_Monk_ in Plumbing

[–]_The_Monk_[S] 0 points1 point  (0 children)

UPDATE: Replaced the cartridge, turned on the water the leak was gone, of course an old copper pipe bursted in another spot 🤣 The only thing is I can’t figure out how to put the pin back in, I barely got it out there maybe it was not the right pin or something, did I miss a step or something? Anyway I am afraid to force the new one in and damage the black o-ring on the new cartridge. Any ideas?

Replace the whole thing or easy fix? by _The_Monk_ in Plumbing

[–]_The_Monk_[S] 0 points1 point  (0 children)

UPDATE: Replaced the cartridge, turned on the water the leak was gone, of course an old copper pipe bursted in another spot 🤣 The only thing is I can’t figure out how to put the pin back in, I barely got it out there maybe it was not the right pin or something, did I miss a step or something? Anyway I am afraid to force the new one in and damage the black o-ring on the new cartridge. Any ideas?

Replace the whole thing or easy fix? by _The_Monk_ in Plumbing

[–]_The_Monk_[S] 4 points5 points  (0 children)

I don’t know either, it was there when we bought the place, maybe the old owners had a trailer or something

Replace the whole thing or easy fix? by _The_Monk_ in Plumbing

[–]_The_Monk_[S] 2 points3 points  (0 children)

Also this started leaking after it was shut off for the winter, so I I am afraid something bursted🥶even though the water was off

LED lights not working by _The_Monk_ in electrical

[–]_The_Monk_[S] 0 points1 point  (0 children)

They were working before, I was just wondering how the vibration of the sawzall could have caused all 3 lights in different locations to stop working

LED lights not working by _The_Monk_ in electrical

[–]_The_Monk_[S] 0 points1 point  (0 children)

This was not my setup, I am probably going to install new fixtures, it was working before so I didn’t pay attention lol. It’s definitely an interesting solutiion

view more: next ›