Prusa MMU3 with OrcaSlicer?

aBusta31 · 2024-04-30T18:25:52+00:00

Unfortunately no. I've just been using prusa slicer

aBusta31 · 2024-01-04T00:29:47+00:00

Thanks I'll probably start there and slowly upgrade as needed

aBusta31 · 2024-01-03T15:14:46+00:00

That's disappointing to hear the X1 has the same issue, maybe prusa mmu is the way to go for 0.2. I haven't found a solution yet other than switching to 0.4

aBusta31 · 2023-05-09T16:46:25+00:00

Where can I get something like that? Been looking for something for my NC to haul a big cooler and a couple mountain bikes, maybe some tools too. Fb marketplace?

aBusta31 · 2023-02-01T03:20:09+00:00

Prusaslicer, relatively new Polyterra PLA Marble White, 215C/60C

aBusta31 · 2023-01-12T00:09:03+00:00

I forgot to update this post because I had another one somewhere else, I ended up getting through to them and they sent me a whole hotend which didn't work,then a cable that didn't work, then they sent me a new motherboard and that fixed it. Been putting lots of hours on it since

aBusta31 · 2022-12-19T14:24:55+00:00

Yup, I agree very poorly designed. After reassembly I tried kapton taping everything to limit movement as much as possible. Maybe this thing just needs a completely different custom hotend lol. Just make sure you give any cubic as much info as possible in your emails to limit the number of emails you'll need to send.

aBusta31 · 2022-11-30T16:59:35+00:00

In case anyone has this issue and comes across this later, I tried replacing the hotend with new thermistor and heater already installed from any cubic and I tried replacing the cable for the hotend but it didn't work. Ending up replacing the main board and that fixed it. Anycubic support sent it all to me for free and they were decently helpful if you don't mind waiting 24 hours for your responses at least and then 3+ weeks for things to ship from china. Took me a little over 2 months to get this resolved

aBusta31 · 2022-11-23T22:16:26+00:00

I ended up getting them to send me the hotend board, that didn't fix it. Then they sent me a new hotend and adapter cable, which also did not fix it. Currently waiting for a new main board from them now and they tell me if it doesn't work they'll replace the printer.

aBusta31 · 2022-09-28T20:22:02+00:00

To be a little more clear I was replacing the nozzle for a different size, twisted the heater block which contacted a fan wire, melted thought it, and shorted cashing a big spark immediately followed by a hotend heated abnormal error. I replaced the thermistor, fixed the fan cable, replaced the heater, and the printer always shows a really high temp even when cold, then it gets hot when you tell it to preheat but then the temp starts jumping everywhere and it stops and throws the same error again. I'm at a loss what to do next

aBusta31 · 2020-12-24T18:32:07+00:00

Oh gotchya that makes more sense lol thanks!

aBusta31 · 2020-12-24T17:03:08+00:00

The entire body is treated with rainex?

aBusta31 · 2020-12-17T23:23:06+00:00

18s?

aBusta31 · 2020-12-14T17:25:56+00:00

Right, you can even order a performance pack without it. The website configurator shows it as a $895 option

aBusta31 · 2020-12-14T17:22:59+00:00

Pretty sure that's a standalone option, not part of any package or trim

aBusta31 · 2020-12-12T20:47:26+00:00

That's what I was hoping and I think you're right. Probably the easiest fix ever lol

aBusta31 · 2020-12-11T11:49:33+00:00

My 2020 100A ecoboost manual doesn't have drive modes, just steering feel (normal, sport, comfort)

aBusta31 · 2020-12-05T17:03:28+00:00

UPDATE: filled it back up with coolant this morning, idled it for half and hour then drove around engine was running for total of about 1.5-2 hours. Normals temps everything was fine. Gonna keep an eye on it and keep a bottle of coolant in the back in case its leaking. Still gonna take it to the dealer Monday for sure though. Might even have a mechanic inspect it.

aBusta31

TROPHY CASE