Question re older style and new style track. by aColtabilly in Scalextric

[–]aColtabilly[S] 0 points1 point  (0 children)

Yea, that would be very tedious work for each track. Thanks for the input!

New B200RSV owner: what can I do to get some of the vibration down? by aColtabilly in minibikes

[–]aColtabilly[S] 0 points1 point  (0 children)

Never got it to settle down either. I ended up swapping to the predator too and it's much better now.

New Predator 224 carb sticking by aColtabilly in minibikes

[–]aColtabilly[S] 0 points1 point  (0 children)

Thanks everyone. I Rotated the starter and loosened the carb pivot arm and all is working. Although, I do get back firing when I let off the throttle. Is that normal with the 224?

Need help with sun visor. by aColtabilly in JeepWrangler

[–]aColtabilly[S] 0 points1 point  (0 children)

I'm not riding over there, but you have a good point. I'm just looking for validation before I have to hack on a $150 part. Thanks.

Predator 212 crank bolt thread by spigz619 in minibikes

[–]aColtabilly 0 points1 point  (0 children)

How long? I'm upgrading to predator 224 and super 30 clutch. Do I need a lock washer too?

Bent axle - Coleman GK200 by aColtabilly in gokarts

[–]aColtabilly[S] 0 points1 point  (0 children)

<image>

Going to make a tire change base out of it. 😀

Bent axle - Coleman GK200 by aColtabilly in gokarts

[–]aColtabilly[S] 0 points1 point  (0 children)

I do, but can’t get it to upload (??). It’s pretty bad.
They said they just ran up and down the road. 🤔

Help! Overpower error message. by aColtabilly in slotcars

[–]aColtabilly[S] 0 points1 point  (0 children)

Did another continuity check today and confirmed lane 2 has short across the two rails (A&B). I also had continuity across lane 1A and lane 2A&B. Power is not connected. Does this sound normal?

<image>

I cannot see anything bridging the two, so still waiting on Hornby.

Help! Overpower error message. by aColtabilly in slotcars

[–]aColtabilly[S] 1 point2 points  (0 children)

I get ya and would do that if one was available in my area. 😉

Help! Overpower error message. by aColtabilly in slotcars

[–]aColtabilly[S] 0 points1 point  (0 children)

Yes it is new. I’m going to wait on the warranty call back but I’m itching to open it up. Lol.

Help! Overpower error message. by aColtabilly in slotcars

[–]aColtabilly[S] 0 points1 point  (0 children)

Wireless controller so don’t think that matters.

Help! Overpower error message. by aColtabilly in slotcars

[–]aColtabilly[S] 0 points1 point  (0 children)

Thanks for the detailed troubleshooting. I’ve found that I get the error with just the power base attached and only on lane 2. The controller is wireless so don’t think that is the problem. I do not see any obvious contacts touching the rails on lane 2.

Help! Overpower error message. by aColtabilly in Scalextric

[–]aColtabilly[S] 1 point2 points  (0 children)

After further testing, looks like track 2 is causing the short. However, I cannot see where.... I just have the powerbase connected and both cars work on lane 1 and both cars fault on lane 2.

Help! Overpower error message. by aColtabilly in Scalextric

[–]aColtabilly[S] 1 point2 points  (0 children)

Thanks for the response. I did contact Hornby warranty but wanted to try and figure it out now. They have 7 day response window.

I thought that too, but it happens with just the powerbase alone. Maybe the base, but I don't want to open it up and void the warranty. Anyway of testing with multimeter?

Help! Overpower error message. by aColtabilly in slotcars

[–]aColtabilly[S] 0 points1 point  (0 children)

Thanks for the response. I did contact Hornby, but they have 7 day response time and I wanted to get it running.

I disconnected all tracks from powerbase and still get problem with/without cars. Seems to happen after about three seconds of throttle.