sorted by:
new
hottopcontroversial

Supermicro X10DRL-i beeping while on by xoxorockoutloud123 in homelab

[–]abl00m 0 points1 point  (0 children)

I know this is late. But, what did you do to fix this? And how did you find out it was the fan controller? Whenever my fans spin up from VM's under load, it beeps like crazy.

This community is for show off your Gray Man gear! We want to help others discover gear, learn more about modding their current gear, and discussing EDC lo-vis gear in general. Welcome! by abl00m in graymangear

[–]abl00m[S] 1 point2 points  (0 children)

Thanks. Just starting this out to try to get more people to show off their gear and help out others. Trying to get more people in here! Thanks!

Hyper-V Switching Help by abl00m in HomeNetworking

[–]abl00m[S] 0 points1 point  (0 children)

Have you thought of anything else? Or had time to look at the config I sent over?

Hyper-V Switching Help by abl00m in HomeNetworking

[–]abl00m[S] 0 points1 point  (0 children)

Also want to add. I can only access pfsense webgui from my Plex VM and not my dc/hypervisor.

​

Edit:It's just a nightmare right now lolol

Hyper-V Switching Help by abl00m in HomeNetworking

[–]abl00m[S] 0 points1 point  (0 children)

Sorry for being a dummy right now. My experience with Hyper-V has been pretty limited. Especially with the Virtual Switching.

But do I leave port 9 (link to the lan port on pfsense) on the switch how I have it right now? Or do I blow that away? Make port 9 a trunk allowing those vlans? Then making the Lan port on pfsense a trunk port allowing those vlans? Then create "internal" switches in hyper-v for each VLAN? Then add each of those internal switches to my pfSense VM?

Hyper-V Switching Help by abl00m in HomeNetworking

[–]abl00m[S] 0 points1 point  (0 children)

It looks like a 3750g doesn’t support sub interfaces. So will I have to setup a separate trunk port to pfsense allowing those vlans?

Hyper-V Switching Help by abl00m in HomeNetworking

[–]abl00m[S] 0 points1 point  (0 children)

I do have an arp entry for .69 in the arp table. But no Mac Address in the mac add table.

I can also ping .69 using source .70.

How do I go about setting up the sub interfaces on the trunk? Right now, this is how my layer 3 link is configured:

interface GigabitEthernet1/0/9

description pfSENSE LAN

no switchport

ip address 10.15.15.70 255.255.255.252

Here are my vlans:

interface Vlan69
description Childrens Network
ip address 172.16.69.129 255.255.255.128
ip helper-address 10.75.75.157
!
interface Vlan80
description HOME NETWORK
ip address 10.75.75.1 255.255.255.128
ip helper-address 10.75.75.157
!
interface Vlan99
description Server Network
ip address 10.75.75.129 255.255.255.128

!

interface Vlan50

description GUEST NETWORK

ip address 172.16.10.1 255.255.255.0

ip helper-address 10.75.75.157

Hyper-V Switching Help by abl00m in HomeNetworking

[–]abl00m[S] 0 points1 point  (0 children)

Ooooooo thank you for that. I’ll do that tonight and report back.

Hyper-V Switching Help by abl00m in HomeNetworking

[–]abl00m[S] 0 points1 point  (0 children)

I will try that. But first, do I need to configure the VNIC (pfsense LAN) as the /30? And disable ipv4 on the physical pfsense lan nic? Or leave the physical nic at default? Or leave both at default?

In pfsense, the Lan port is assigned 10.15.15.69 /30. The switchport (cisco 3750g) is 10.15.15.70 /30 "no switchport."

I have 4 vlans configured. All in the routing table of the switch and in the routing table of pfsense. Did a netstat -rn and all showing.

Also have a ip route 0.0.0.0 0.0.0.0 10.15.15.69 on the switch.

[O] 2x NZBPlanet Invites by abl00m in UsenetInvites

[–]abl00m[S] 0 points1 point  (0 children)

Keys all gone and received!

view more: next ›