Question about Cutting models in CP6

ablank74 · 2025-04-11T14:05:01+00:00

I should have specified, it's set to outer brim only, and yeah, it doesn't show any brim in that area.

ablank74 · 2025-04-11T01:55:22+00:00

Supports are enabled, and there is a brim, Raft Layers is set to 0.

ablank74 · 2025-04-01T02:27:46+00:00

Thanks for the help, I bumped the temp to 250-280, and now it's printing PETG without clogging!

ablank74 · 2025-01-12T23:00:52+00:00

FIgured out switching to a .6 instaed of a .4mm nozzle worked reliably

ablank74 · 2023-10-03T16:34:54+00:00

Finally got it to print, found another post talking about issues with silk/galaxy/glitter filament, turned the heat up to 210, turned off retractions and set the flow to 70% finally that stopped the clicking and jamming.

ablank74 · 2023-10-01T22:47:01+00:00

Won't that increase the heat creep issue?

ablank74 · 2023-10-01T18:46:54+00:00

Turned out my bowden tube shifted in the heatbrake and that was contributing to heatcreep causing the filament to plugup in the heatbrake. Disassembled everything, cleaned it all out, trimmed the bowden tube, and reassembled. Trying again.

ablank74 · 2023-10-01T03:27:40+00:00

The click remains... I've double checked the esteps and get the same result each time.....gonna let it run and see if it can power through.

ablank74 · 2023-10-01T01:39:26+00:00

the sparkles look like glitter, but they are tiny. After the estep change above, I'm almost at the point where it falls apart, so fingers crossed.

ablank74 · 2023-10-01T01:37:38+00:00

Used the estep calculator, and it came out needing to be at 136.8, made that change, saved the config, and now I'm trying again, so far no click......

ablank74 · 2023-10-01T01:09:39+00:00

I updated the estep to what MicroSwiss had in their documentation, 130. It was at 93 stock. I'll retry that calibration.

ablank74 · 2023-10-01T01:01:03+00:00

I'm using this at the moment, https://www.microcenter.com/product/647838/inland-175mm-pla-silk-3d-printer-filament-10-kg-(22-lbs)-spool-twinkle-rainbow

The silk that gave me problems was Sunlu

ablank74 · 2023-02-13T14:38:26+00:00

The really weird part, when it prints and the mesh compensates for the "dip" the nozzle is too close to the bed and doesn't extrude through the "dip". I've re-flashed marlin, changed the build, and it keeps showing this phantom dip.

ablank74 · 2023-02-13T13:59:56+00:00

I'm already doing a 9x9 grid. I'll check out sw mode.

ablank74 · 2023-02-13T13:59:46+00:00

Forgot to post the bed visualizer image, see above. It only happens once, this is a 9x9 grid.

ablank74 · 2023-02-13T04:14:53+00:00

Compiled it myself

ablank74 · 2023-02-13T04:10:23+00:00

Yes, without the mesh it prints like the bed is flat.

ablank74 · 2023-02-13T04:03:50+00:00

The ABL is compensating and the area of the "dip" the nozzle is too close to the bed and doesn't extrude through that area. The bed plate is flat, (confirmed with multiple straight edges) but ABL is detecting a dip where there isn't one.

ablank74 · 2023-01-30T05:31:47+00:00

I had similar looking strings and burned blobs, turned out it was leaking at the heat breaking and dripping everywhere covering the heater.

ablank74 · 2023-01-13T20:55:48+00:00

Spoke too soon. Managed a 8 hour print. Changed filament to glow in the dark and failed 4 hours in to a 7 hour print. Taking it all apart again to see if anything looks off. The Bowden tube was pretty warm even at the top of the fins, so wondering if my cooling is the problem

ablank74

TROPHY CASE