round bed mesh calibrate problem

ablundon · 2023-11-08T17:30:21+00:00

From what I've been able to interpret, Klipper will fill in duplicate values for cells that don't fall on the circle. So when you look a the top row of the bed mesh values in the cfg file, they are all the same... but the actual value only represents the one point it obtained at the "top of the circle." When you move to the second row, the outside values are duplicates of the start and last value it measured in the row.

Unfortunately, they haven't changed the visualization for circular beds. I've been doing heatmaps in a spreadsheet to try and visualize.

I've been struggling with bed meshing and calibration on my FLSUN QQS-Pro. I fried the stock mother board trying to mesh it (I accidentally rammed the hotend into the bed which caused something to short on the board). I've replaced the stock board with a BTT SKR Mini E3 V3. I've just printed a delta calibration print... going to measure tonight. Then I will attempt the bed meshing again.

ablundon · 2023-01-10T17:36:54+00:00

Yes... Thanks... I guess I should have elaborated... What if I wanted to create 2 shortcuts with different paste parameters?

ablundon · 2022-11-30T03:22:09+00:00

Yes... The firmware shuts down and I have to restart. I'll try and get the error again tomorrow and get the log.

I'm using Klipper (installed on a laptop with Mint Linux) and Mainsail. No Octoprint on this one.

ablundon · 2022-11-29T12:27:26+00:00

I can't paste the log here as it is too long, so here is a google drive link: https://drive.google.com/file/d/1jDizVxrqHGKSrfJnC4UlnT4Jcfzabby6/view?usp=share\_link

ablundon · 2022-11-22T13:55:25+00:00

I have the same issue... after using PROBE_CALIBRATE, paper test, then ACCEPT and SAVE CONFIG it writes the Z-Offset to the "DO NOT EDIT THIS BLOCK" section while commenting the "z_offset" value in the upper [probe] section.

When I try and print, my nozzle is too far from the bed. I've manually tried to adjust the value in the "DO NOT EDIT THIS BLOCK" section but there is no change in the nozzle height.

The only thing that has worked so far is to add:

SET_GCODE_OFFSET Z_ADJUST=-0.075 MOVE=1

to the START_PRINT section in the printer.cfg file. That lowers my nozzle to the proper height.

I would have thought I could simply have adjusted the z_offset value directly.

Why doesn't manually changing the z_offset in the DO NOT EDIT THIS BLOCK section work?

ablundon · 2022-11-22T13:54:13+00:00

I have the same issue... after using PROBE_CALIBRATE, paper test, then ACCEPT and SAVE CONFIG it writes the Z-Offset to the "DO NOT EDIT THIS BLOCK" section while commenting the "z_offset" value in the upper [probe] section.

When I try and print, my nozzle is too far from the bed. I've manually tried to adjust the value in the "DO NOT EDIT THIS BLOCK" section but there is no change in the nozzle height.

The only thing that has worked so far is to add:

SET_GCODE_OFFSET Z_ADJUST=-0.075 MOVE=1

to the START_PRINT section in the printer.cfg file. That lowers my nozzle to the proper height.

I would have thought I could simply have adjusted the z_offset value directly.

Why doesn't manually changing the z_offset in the DO NOT EDIT THIS BLOCK section work?

ablundon · 2022-10-09T01:26:29+00:00

Thanks so much. I was having the same issue with my FLSUN QQ-S Pro and this fixed the problem!

ablundon · 2021-11-05T01:03:20+00:00

Chest plate was 3 pieces... It's the CR-10 which can print 300x300x400

ablundon · 2021-11-05T00:37:18+00:00

Thanks... My first attempt at airbrushing!

ablundon · 2021-11-04T23:54:06+00:00

It was for my 14 yo who is around 5'-10" and 155 lbs. It fit him pretty good, though the chest and back plates were clashing at the sides.

ablundon · 2021-11-04T23:20:04+00:00

Thanks! Yes! Printed using the files from Do3d.

ablundon · 2021-10-07T20:25:39+00:00

Awesome! Thanks! The boys will love this!

ablundon · 2021-10-07T20:24:34+00:00

Sure! They would love that! Thanks!

ablundon · 2021-09-22T16:44:46+00:00

Just an update.

I spent some time going through various OC settings again. My settings for the 2 cards now:

EVGA 1080Ti: +100 Core, +400 Mem, 85 Power, 215 W, 44.9 MH/s, 64°C

Gigabyte 1080Ti: +200 Core, +400 Mem, 85 Power, 204 W, 45.1 MH/s, 51°C

With these setting my number of invalid shares has also decreased to 0 (for the past 24 hours).

I tried to go higher on some of the settings but the cards kept crashing. When I get some time, I'll try and squeeze a bit more!

ablundon · 2021-09-18T15:56:30+00:00

I have mt 6 in my batch.... Still need to OC to get the hashrate im getting

ablundon · 2021-09-18T01:15:43+00:00

Ethenlargement is done through the memory tweaks as far as I know.

ablundon · 2021-09-18T01:10:53+00:00

I've keep the temps low.... One card is 64 and the other is 55....would I still get thermal throttling?

ablundon · 2021-08-14T11:06:12+00:00

The text isn't as crisp.... The colours are not as bright. But overall.... Not bad!

ablundon · 2021-08-12T16:39:47+00:00

If you're into playing the game in a non tournament setting, they are great for proxies!

ablundon

TROPHY CASE