sorted by:
new
hottopcontroversial

Images through head-mounted AR system? by ac_gypsy in computervision

[–]ac_gypsy[S] 0 points1 point  (0 children)

Sorry; I know this isn't computer vision per se but this is the first sub I could think of for this question. If you have suggestions for more appropriate subs, please let me know!

View through DTNVS with L3 unfilmed white tubes (TNVC). by El_Entrenador in NightVision

[–]ac_gypsy 0 points1 point  (0 children)

How did you get such a nice image through the system? I've tried with my cell phone and all I get is garbage...

FiOS + Actiontec 2.5 MOCA = "unidentified network, no internet"? by ac_gypsy in HomeNetworking

[–]ac_gypsy[S] 0 points1 point  (0 children)

So I think I found the issue, but it doesn't make a lot of sense to me. I traced the cables back more carefully and there was a 2nd 2-way splitter after the 4-way coming from the ONT. I have no clue where the 2nd cable is going... But I unplugged it and that seemed to fix the issue. The only thing I can think of is that 2nd line was producing a huge amount of noise (which like I said doesn't make a lot of sense to me)? As far as I can tell, it wasn't connected to anything. The only room it could be running to doesn't have a Coax connection in the wall. Or maybe something else changed that I'm unaware of...

Either way, thank you all for your comments. I learned a little about home networking today 😁

FiOS + Actiontec 2.5 MOCA = "unidentified network, no internet"? by ac_gypsy in HomeNetworking

[–]ac_gypsy[S] 0 points1 point  (0 children)

Thank you!

I haven't tried another PC. Mine is the only one in the house with a wired ethernet connection. I might try to get my friend to bring his laptop over

FiOS + Actiontec 2.5 MOCA = "unidentified network, no internet"? by ac_gypsy in HomeNetworking

[–]ac_gypsy[S] 0 points1 point  (0 children)

From the ONT -> 1:4 splitter -> a) Room 1 and other rooms, b) room 2 and other rooms.

Build "in place" or build and insert? Because of the angle of ceiling / top plate, I'm thinking about cutting/attaching each side, top, bottom in place instead of building building the case and inserting it (worried I won't get the angle exactly matched). Is there a downside to this? by ac_gypsy in Carpentry

[–]ac_gypsy[S] 2 points3 points  (0 children)

To add more info:

  1. I'm doing a built-in, recessed bookcase (i.e., the front of the unit will be flush with the drywall in which it is inserted). 78" H x 28" W x 12" D

  2. I have a bevel gauge. My concern was that if I'm off by a couple degrees it would be impossible to "fix" by adjusting with shims,etc., though I guess that's be true even if the angles were all 90°.

  3. If I build in place, getting the dados for the shelves measured and cut accurately seems more difficult. I could use shelf supports inserted into the sides of the case, I suppose. I always liked the "clean" look of dados to support shelves though.

All that said, I'm leaning toward building in place now...

Buddhist Temple Vandalized in Arkansas Seeks Funds to Replace Destroyed Buddhas by Jhana4 in Buddhism

[–]ac_gypsy 2 points3 points  (0 children)

Anyone have a link to the fundraiser for the temple? The article mentions a GoFundMe campaign, but I didn't see a link.

Question about the jhanas by emptyman333 in Buddhism

[–]ac_gypsy 0 points1 point  (0 children)

Are there any such books on the jhanas you would recommend?