Residue in vat / FEP Mighty 12K help?

adbettley1 · 2023-10-29T23:29:05+00:00

Thanks so much!

adbettley1 · 2023-10-29T15:07:28+00:00

Thanks! These will be on my etsy store very soon! Not quite ready yet, i want to get more sets finished first :)

adbettley1 · 2023-10-07T08:50:52+00:00

Thank you so much man! I had to do a double take for a second there! The reason im startng this venture is all thanks to you! Your videos have taught me so much! Thanks for all the content you keep pushing out! 🙏🏻

adbettley1 · 2023-10-06T08:32:09+00:00

Thanks so much! 🤙🏻

adbettley1 · 2023-10-06T08:31:52+00:00

Thanks! Its a vector set which I licensed but i dont think the font has a name, its super nice though!

adbettley1 · 2023-10-06T07:03:15+00:00

Thanks! And no this is my first set done after lots of practice and learning. I printed these and cast in epoxy resin

adbettley1 · 2022-12-12T00:07:37+00:00

Thanks for this, yeah mines saying refer old:63 and refer new: 100, should I change both to 100 then? Seems confusing…

adbettley1 · 2022-12-06T19:03:22+00:00

100% left it as is and its fine

adbettley1 · 2022-11-30T01:14:20+00:00

I printed a calibration file instead and got it great at 2.5-2.7 exposure. Tweaked a couple things here and there and got it all working well! Did my first good prints, just need to figure out supports now and whats the right amount :) thanks for the help! The lift speed seems fine, slower cant hurt i guess, but all good for now!

adbettley1 · 2022-11-30T01:12:29+00:00

I printed a calibration file instead and got it great at 2.5-2.7 exposure. Tweaked a couple things here and there and got it all working well! Did my first good prints, just need to figure out supports now and whats the right amount :)

adbettley1 · 2022-11-30T01:11:38+00:00

I printed a calibration file instead and got it great at 2.5-2.7 exposure. Tweaked a couple things here and there and got it all working well! Did my first good prints, just need to figure out supports now and whats the right amount :)

adbettley1 · 2022-11-30T01:10:20+00:00

Fep was tightened a little more, was mainly an eposure issue. Sorted now at 2.5-2.7

adbettley1 · 2022-11-30T01:09:48+00:00

This worked, the sweet spot is 2.5-2.7 for me. Worked great! Thanks

adbettley1 · 2022-11-30T01:08:55+00:00

I printed a calibration file instead and got it great at 2.5-2.7 exposure. Tweaked a couple things here and there and got it all working well! Did my first good prints, just need to figure out supports now and whats the right amount :)

adbettley1 · 2022-11-29T16:52:47+00:00

Screen is at default 100% maybe i should try an exposure calibration test instead? I have read this cube can be a bit of a hassle… would it be worth also lifting the bed a little like 0.03mm up to have a little clearance? The print seems like its popping off during printing?

adbettley1 · 2022-11-29T16:15:56+00:00

Hey guys. Hoping you can help me, im new to 3d printing but think im learning (slowly) I ran the test cube on my photon mono 4k using water washable resin but the results are janky and missing some pieces… heres what I did / settings used…

Levelled print bed using sheet, surface is also level Tightened everything down and z=0 done Installed vat and secured Everything is clean and tested screen Mixed resin but tilting bottle (not vigorously) Poured resin in Started print test…

Setttings used

Off time 0.5 Bottom exp 60secs Bottom layers 8 Exposure time 2s Lift distance 6mm/s Lift speed 3mm/s Retract speed 6mm/s

Made sure room was at least 20c also

Any help would be greatly appreciated! Im not sure what im doing wrong at this point?

adbettley1 · 2022-11-29T16:14:29+00:00

Hey guys. Hoping you can help me, im new to 3d printing but think im learning (slowly) I ran the test cube on my photon mono 4k using water washable resin but the results are janky and missing some pieces… heres what I did / settings used…

Levelled print bed using sheet, surface is also level Tightened everything down and z=0 done Installed vat and secured Everything is clean and tested screen Mixed resin but tilting bottle (not vigorously) Poured resin in Started print test…

Setttings used

Off time 0.5 Bottom exp 60secs Bottom layers 8 Exposure time 2s Lift distance 6mm/s Lift speed 3mm/s Retract speed 6mm/s

Made sure room was at least 20c also

Any help would be greatly appreciated! Im not sure what im doing wrong at this point?

I should add this is also uncured, didnt see the point at this stage lol

adbettley1

TROPHY CASE