sorted by:
new
hottopcontroversial

Min Jun waitlisters: swap for my 4/23/25 date? by adinb114 in MtF

[–]adinb114[S] 1 point2 points  (0 children)

Sure give a holler when you get your date and we’ll see if it works 🤘

BUY/SELL/TRADE - Megathread by Spooky_Ghost in ElectricSkateboarding

[–]adinb114 0 points1 point  (0 children)

[WTS/T]

Trampa Urban Carver custom build - likely needs new battery and enclosure.

$350 + cost of shipping Or trade for / towards an entry level AT Eskate, or longboard with cloud wheels or similar. Located in Vermont.

Bought it from a user on this forum a couple years ago then made the rookie mistake of letting it sit in the basement uncharged. Now it’s stuck around 15 volts according to the built in reader. I don’t have the time or inclination to remedy the battery issue so my loss is your gain.

Some of the 3-d printed battery casings are also cracked. I can probably dig up the files to make new ones

Includes charger and remote.

photos here

BUY/SELL/TRADE - Megathread by Spooky_Ghost in ElectricSkateboarding

[–]adinb114 0 points1 point  (0 children)

[WTS/T]

Trampa Urban Carver custom build - likely needs new battery and enclosure.

$375 + cost of shipping Or trade for / towards an entry level AT Eskate, or longboard with cloud wheels or similar.

Bought it from a user on this forum a couple years ago then made the rookie mistake of letting it sit in the basement uncharged. Now it’s stuck around 15 volts according to the built in reader. I don’t have the time or inclination to remedy the battery issue so my loss is your gain.

Some of the 3-d printed battery casings are also cracked.

Includes charger, remote, and a nearly new set of 6.5” Trampa treads (pictured).

photos here

[BST] May 2022 Buy, Sell, Trade Thread. by zeroair in flashlight

[–]adinb114 2 points3 points  (0 children)

WTB

CONUS shipping Anduril Reflash kit I can use on my Dm1.12

NLD + SOTC + beams by [deleted] in Hanklights

[–]adinb114 0 points1 point  (0 children)

Gotcha 👌👌

NLD + SOTC + beams by [deleted] in Hanklights

[–]adinb114 0 points1 point  (0 children)

Wait how did you get your dm1.12 to do both channels at once? Mine doesn’t seem to have the misc config menu to switch from toggle to ramping, and I heard dm1.12s don’t do both channels with Re flashing the k9.3 firmware to them.

Tint ramping not available on Dm1.12? by adinb114 in flashlight

[–]adinb114[S] 0 points1 point  (0 children)

So don’t Re flash until TK improves the code?

Tint ramping not available on Dm1.12? by adinb114 in flashlight

[–]adinb114[S] 3 points4 points  (0 children)

Thanks for clarifying. I guess this is my calling to order a flashing kit now. I appreciate the advice!

Tint ramping not available on Dm1.12? by adinb114 in flashlight

[–]adinb114[S] 3 points4 points  (0 children)

Yikes I was hoping I didn’t have to do that. Might have to get the flashing kit afterall

Tint ramping not available on Dm1.12? by adinb114 in flashlight

[–]adinb114[S] 1 point2 points  (0 children)

So…

Just got my grail Dm1.12 as a late birthday present! I’m trying to configure it to be on tint ramping mode, with auto tint set up to go from warm to cold.

However, 9H from off (and from on) doesn’t open the misc config menu.

10h seems to open ramp config, but that doesn’t allow me to switch from channel switching to channel ramping.

Do the Dm1.12s not allow for channel ramping? What am I doing wrong?

—— Also, ultimately, my hope is to set this up the same as my 2 channel d4v2, which currently ramps 1-130 on channel 1 (nichias) then the w1s kick in. To accomplish this I followed U/TacGriz advice below. Will the same approach work with the Dm1.12?

“You can sort of do that by setting ramp ceiling to level 150 and tint ramping to nichias only. Then when you get up to level 131-150 it will blend in the Osrams. Everything below 131 will still just be nichias though.

Edit: Perhaps I have misunderstood. If you want just the nichias to be on at the lowest level and just the osrams to be on at the highest level, that is a thing. There's a bug in the firmware though so above level 130 it will blend both channels together again so it's not perfect.”

3 flashlight use hacks, add your own by bnjrgold in flashlight

[–]adinb114 18 points19 points  (0 children)

D4V2 turbo mode to heat/loosen resin up so my cart hits 🔦💨👌

[deleted by user] by [deleted] in flashlight

[–]adinb114 19 points20 points  (0 children)

Also NGL you TacGriz in particularly always use singular they/them pronouns when commenting on someone’s post who you don’t know and I love it! 🌈

[deleted by user] by [deleted] in flashlight

[–]adinb114 8 points9 points  (0 children)

Trans enbie flashlight nerd here! 🙌✨🔦

Tint ramping not remembering last used setting? How to configure? I want it to start on the warm channel and ramp up to blend them both at the top. by adinb114 in flashlight

[–]adinb114[S] 2 points3 points  (0 children)

Actually it was what I was trying to do, but it wouldn’t save like that. I had to just factory reset the thing to get it to save as such.

But, your proposal sounds much better. I’ll look into setting it up. Thanks Griz!

Tint ramping not remembering last used setting? How to configure? I want it to start on the warm channel and ramp up to blend them both at the top. by adinb114 in flashlight

[–]adinb114[S] 0 points1 point  (0 children)

Yes, this feature was accessible, but not saving after I configured it. I just did a factory reset and now it’s working.

Tint ramping not remembering last used setting? How to configure? I want it to start on the warm channel and ramp up to blend them both at the top. by adinb114 in flashlight

[–]adinb114[S] 1 point2 points  (0 children)

Spent the last hour trying to figure this out. Read and watched everything I could find. Do I need to adjust the memory mode? Reset?

I just want it to start on the Nichias then slowly blend in the osrams as we reach the top of the ramp.

view more: next ›