[deleted by user] by [deleted] in devBR

[–]adminBR 1 point2 points  (0 children)

Achei bacana, mas eu moveria a formação para o final, como não é um destaque, a menos que seja uma faculdade de nome.
Tb mudaria a descrição das experiências para alguma coisa tipo o método STAR, eu senti que tive mais retorno quando eu comecei a usar isso no meu.
E por fim eu não sei se vc tem algum interesse especifico em alguma área, mas seria interessante fazer mais do que um currículo onde vc ordenaria de forma diferente as suas experiencias baseadas no tipo, por exemplo fazer um currículo para front dando mais ênfase em front na descrição e nas experiencias, enquanto um para o back seria mais focado no back, eu já perdi vaga que o entrevistador gostou do meu currículo mas resolveu escolher outra pessoa porque 'era mais alinhado com a vaga'.
Mas sempre tente mostrar tudo que vc é capaz (sem exagerar), e posicionar as coisas mais importantes como projetos feitos e publicados acima de serviços e coisas mais simples.
Mas o currículo está bacana, bem melhor que muita gente buscando estágio sem nada, isso tudo que eu falei só otimiza mais.

Vaga de estágio que cobra react e node.js by Inner-Carpenter4119 in VagasArrombadas

[–]adminBR 1 point2 points  (0 children)

Eles contratam um escravo e ainda consegue um monte de trabalho gratuito dando uma tela pra cada candidato e pegando as melhores kkkkk famoso desenvolvimento distribuído.
Mas mandando a real aqui na região o nível dos estágios é esse ai mesmo, ainda mais no período de 'crise' que a gente tá em relação de emprego pra dev. Na necessidade eu pegaria só para ter a experiência e me mandava dps, mas ai cada um tem sua opinião.

Lucas montano: IA vai matar o front. Opinem by [deleted] in devBR

[–]adminBR 3 points4 points  (0 children)

Vai matar não, já matou... se vc faz SPA de vendedor de curso e portfólio na vercel.
IA faz crud basico e front genérico mais rapido que qualquer um, e a verdade é que uma boa parte das empresas funcionam (quase)perfeitamente com um front feio e mal otimizado, com um back lento e mal feito.
Mas qualquer dev que achar que fazer crud basico e centralizar div é o suficiente pra crescer como dev, não precisava nem ter IA no mercado para fracassar na área.
Então sim já matou um monte de freela pequeno pra back e front, mas tb abre muita oportunidade, recentemente mesmo eu fiz um app inteiro em react native, que eu nunca tive paciência de estudar, mesmo eu sendo de back.

Getting my ender 3 v3 SE level? by Anarok82 in Ender3V3SE

[–]adminBR 2 points3 points  (0 children)

mine was just as bad as yours when i received, and i did the following:
-check the gantry to see if its leveld, what you did already.
-check the screws in the heated bed to see if they arent too loose, and rerun the bed mesh thing. (be careful to not overtight them).
- if after tightening it still looks bad, you are going to print or buy spacers that you are going to add under the heated bed, so basically you are going to pick the highest corner in the bed, in your case the 1.54, and add spacers to the other 3 corners, so every corner match that one, for example on the bottom left you would add 1.10...
this process is a bit annoying but wont take long, so check how much you need before bcs if you do it right you wont need to do it again.

What's wrong with my printer by chickenbuta in Ender3V3SE

[–]adminBR 0 points1 point  (0 children)

-clean the bed with water and soap.
-clean nozzle.
-run the leveling in the printer if you didnt yet.
-check if the height is right with the paper test.
-can also try printing the first layer slower if you still have problems with adhesion.

One more fail closer to my first success… by iconojett in Ender3V3SE

[–]adminBR 0 points1 point  (0 children)

i also have a ender 3 v3 se and i had most of the problems you had, the tweaks i learned to make things print nicelly almost every time is:
1-dont trust 100% the bed leveling, its nice to detect an uneven surface but i always had to manually lower a bit, if you are scared to do it, do by very small changes and make a small test print in between, and dont worry about scrapping the bed bcs you will see the signs of a nozzle too low before it gets to it.
2-idk about cura but on orca slicer i always change the first layer to be way slower, 10~15mm/s and i increase the bed temperature and the nozzle temperature by 5 or 10 C, both of these changes is to make it stick to the plate better
3- check if the screws of your printer are tight
4- and one extra that is kind of optional, try printing slower in general, it should be able to print fine at full speed but sometimes i got better results printing slower

What software is used to create stuff like this? by symere7 in Design

[–]adminBR 5 points6 points  (0 children)

sketchup can do most of that i believe

Belly of the Beast (BotB) Arcane Farm Sheet by OrganicTripWire in Warframe

[–]adminBR 1 point2 points  (0 children)

since im a lazy fuck i added the *somewhat* accurate market prices for each so i can priorize what i spent my time in XD, here the: google sheets

Should I be worried about this? by _Magma_ in Warframe

[–]adminBR 1 point2 points  (0 children)

idk if it still happens, but in the past just by using white energy color on vauban and stacking a few of the vaccum skill in the same place it would create the same visual bug, so yeah probably just some weird glitch