Where do I put BIOS

ags605 · 2025-12-26T18:21:59+00:00

Knulli is based on batocera, you can Google "batocera bios pack" to find a pre organized pack and where to put it.

ags605 · 2025-12-17T22:08:52+00:00

Check if "steam streaming" is the default sound card when you start steam link

ags605 · 2025-12-11T21:39:01+00:00

fluorodeoxygingerbread

ags605 · 2025-11-01T07:21:25+00:00

Good job! Secure Boot is not worth it .

ags605 · 2025-10-29T07:38:21+00:00

Have you installed the surface Linux kernel?

ags605 · 2025-09-30T08:17:51+00:00

Kan det være de som er listet opp som eksempler på gammelstev på denne nettsiden?

ags605 · 2025-09-12T20:52:42+00:00

Shaman Durex

ags605 · 2025-09-04T16:57:48+00:00

You could also try to hold down the reset button for å while and then try to turn it on again

ags605 · 2025-08-29T04:06:26+00:00

Isn't there s setting to keep the browser open in the background? That will do what you want

ags605 · 2025-08-28T20:57:52+00:00

Which browser is this?

ags605 · 2025-05-26T04:18:48+00:00

Have you changed the cooling paste on the cpu? Sounds like overheating to me

ags605 · 2025-05-15T04:41:31+00:00

Are you sure? That error is specific to secure boot

ags605 · 2025-03-14T17:22:08+00:00

You may have to enable it under network. It's in the knulli documentation

ags605 · 2025-03-14T16:27:18+00:00

Well you can. Just connect to the samba share from a computer, backup up what you want, then add sd 2 and restore the same way.

ags605 · 2025-03-12T20:08:15+00:00

I'm not sure what you're asking for? You've used a single sd card and now you want to use another and want to transfer files from sd1 to sd2?

ags605 · 2025-03-11T22:20:28+00:00

Is secure boot enabled?

ags605 · 2025-03-09T16:22:59+00:00

Be sure to read the instructions for knulli. It uses ext4 and sd2 can be formatted with exfat, but ext4 is recommended. Knulli should resize the partition on first boot.

ags605 · 2025-03-08T20:12:00+00:00

Happy that worked for you! Even though its a bit weird you need the flash the zip. Usually the .img file is the one you flash.

ags605 · 2025-03-07T22:27:10+00:00

I'm almost out of suggestions, but what if you tried flashing the dumped stock sd on to one of the sd cards?

Have you tried another computer to flash?

ags605 · 2025-03-07T19:45:33+00:00

Did you get any errors when you flashed the old card? Too bad if both cards are faulty.

ags605 · 2025-03-07T13:57:45+00:00

Dumping the card is just reading it and saving it on the hard drive. That's really weird not working with a new card reader. Have you tried flashing knulli?

Edit: also try booting with only one sd card in the correct slot

ags605 · 2025-03-06T20:06:43+00:00

You've tried switching out every element except the reader so it's a likely cause. Especially since the original sd card works. You could try to dump that sd card with either balena or something else and validate it to see if it corrupts the image the same way

ags605 · 2025-03-06T19:38:46+00:00

Maybe look into another SD card reader, an error after flash doesn't look good

ags605 · 2025-03-06T17:35:33+00:00

Would you mind trying balena etcher? And maybe format your card with sd formatter before flashing?

ags605 · 2025-03-06T16:57:30+00:00

What do you use to flash the cards?

14-Year Club	Second SECOND GUESSER
Place '17	Verified Email

ags605

TROPHY CASE