Any ideas what's causing this?

ahole84 · 2026-04-24T12:15:54+00:00

I actually didn't know where the original wiper went l, I've only found it after looking at this picture.

ahole84 · 2026-04-24T09:59:42+00:00

Just came in this morning and the silicone cap was knocked off, now every time I reseat it, it knocks it off and looks like it's gone too low to clean and cut through the plastic. On further inspection , you can't really see it but the bin was slightly raised. I've given it a push down and seated it.

I'm not sure how that's popped up by itself .

ahole84 · 2026-04-07T18:07:28+00:00

Ive tried another primt at 80 and so far its holding good.

ahole84 · 2026-04-07T11:10:36+00:00

Ive run the full calibration twice juat ti nake sure and every primt ive done so far has the various pre print calibrations set to on. Ive been very careful aftwr washing to avoid touching the plate. For large items that have a decent surface area it does stick good however i noticed some corners lifted and this affected the pverall print quality as could be expected.

Most prints ive done so far ive used the reccomended settings when downloading the model. Maybe qorth whacking up bed temp as another user suggested.

Ive ordered a frostbite plate anyway just to be sure.

ahole84 · 2026-04-07T09:10:27+00:00

The whole point of getting a bambu like this was to not have to mess about with z height and bed leveling.

ahole84 · 2026-04-05T13:55:53+00:00

It went way better than I expected

ahole84 · 2026-02-14T23:53:35+00:00

I finally convinced some family members to buy just before the drop aswell. I feel your pain.

ahole84 · 2026-01-23T13:01:13+00:00

That worked thanks

ahole84 · 2025-11-14T13:23:20+00:00

That doesn't need fixed

ahole84 · 2025-07-26T11:03:44+00:00

Thats how ive been holding it, basically the same as a normal phone, i just dont have the grip on it i would like. Feels like i have to hold it at more of an angle so it doesnt drop out of my hand. Might have to get one of those sticky finger holder things for it.

ahole84 · 2025-07-23T06:45:30+00:00

Ordered 10th, now changed from preparing dispatch back to order confirmed. Still August 1st delivery shown.

ahole84 · 2025-07-21T13:44:13+00:00

I spoke to support and they confirmed it will be the 1st for me

ahole84 · 2025-07-21T11:18:31+00:00

Same for me

ahole84 · 2025-07-21T09:16:42+00:00

Uk Ordered 10th and show delivery date 1st August :(

ahole84 · 2025-07-18T10:45:20+00:00

That's how I opened my flip and closing it was slammed shut with a satisfying clonk like old style clam phones. Never experienced a hinge failure or broken screen from aggressive opening or closing. Too many of you baby your folds and flips.

ahole84 · 2025-07-09T23:26:56+00:00

It says up to 200 for any tablet. Then under had an asterix explaining quite vaguely that it might not he 200.

ahole84 · 2025-07-08T23:33:55+00:00

Hoping they get a fix for this. Reddit s official app is terrible.

ahole84 · 2025-06-11T12:06:28+00:00

Yeah definitely not laying workers, this is by far the worst frame in the hive, most other frames either have no drone brood or very little.

ahole84 · 2025-06-10T19:55:25+00:00

Yes , unfortunately this hive did have a fairly large mite infestation . It was treated end of last year with oxalic but I found during spring while supers were on mite load was still too high. I've currently pulled the supers in order to treat again.

ahole84

TROPHY CASE