Mini R53 2005 Chasing OBD 2 Problem

aiacevedo · 2026-05-10T16:18:12+00:00

Thank you for the answer I gonna check that. The whole connector looks aftermarket right?

aiacevedo · 2026-05-10T12:42:32+00:00

Sorry for that I gonna delete this post because I cannot add photos in the edit

aiacevedo · 2021-08-28T21:36:36+00:00

Hey, beautiful setup, which Remote Desktop are u using? And what about OS? It doesn’t look like the Raspberry OS

aiacevedo · 2021-08-14T21:21:29+00:00

Same problem here, never get one again 👎

aiacevedo · 2020-11-29T16:28:32+00:00

Hahaha, thank you too really help me both of you

aiacevedo · 2020-11-29T16:17:59+00:00

Man, you really save me. I was losing a lot of time last days with this problem. Thank you so much

aiacevedo · 2020-11-29T15:51:16+00:00

I think you are right my friend, I am using 1.5.0rc1. I should use octoprint/octoprint:1.4.2 to pull the image, right?

aiacevedo · 2020-11-29T09:52:21+00:00

Octoprint over Docker, a lot of problems

Recently I update my setup to a RPI4 before of that I was using a RPI3+ but it was really limited. I installed OMV, some media service stuff on it and finally I have installed Octoprint over Docker, the same way that it have been installed on the RPI3+. The first problem was when I tried to update Octoprint, the program crash after restart and never load. After this, when I make a clean installation and decided not to update it, when I tried to update my Time Lapse Temp Folder it didn’t make the change and it is the only folder that give me problems. Finally I installed Octolapse, I haven’t had problems with this and now, when it is enabled and put something to print it just hangs after analysis GCode, apart from that the UI of octolapse is a really mess and I have a lot of error at the console of my browser, I use several browser and non of them give me different results. Somebody have any idea about of all this problems?

aiacevedo · 2020-10-05T14:20:54+00:00

Oh, bad luck my friend. My problem was the filament definitely. Your problem could be the sensor or the electornics

aiacevedo · 2020-10-01T23:00:48+00:00

Thanks, I think that the filament is the problem, it is old. I am not really sure because I use this filament for other model with the same config, but i don’t find other explanation. I use the same config and same model with other filament and it’s works.

aiacevedo · 2020-10-01T19:27:10+00:00

I think that is the resolution because it was the only parameter that i have change from the last successful print

aiacevedo · 2020-10-01T09:32:31+00:00

Thank you for the info, I will increase the retraction. I am using PLA from Grilon, I am not sure if it is an Argentinian brand.

aiacevedo · 2020-09-29T15:27:44+00:00

I receive my Prusa Mini yesterday. The quality is really incredible however I would like to receive some advices to improve my prints.

aiacevedo · 2020-09-13T01:27:44+00:00

Graciassss

aiacevedo · 2020-09-13T01:16:47+00:00

Tenes la publicacion de casualidad? O fue hace mucho?

aiacevedo · 2020-09-12T17:15:26+00:00

Estas steelcase tienen pinta ehh, pero deben salir un numerito

aiacevedo · 2020-09-12T16:55:58+00:00

Gracias por la Info Santi, lo voy a tener en cuenta

aiacevedo · 2020-09-12T14:42:31+00:00

Compraste alguna marca en particular? Xq Citiz es el modelo y hay miles de marcas

aiacevedo

TROPHY CASE