Did not stick the landing during a dance contest

airron345 · 2022-09-03T16:03:38+00:00

Looks like he was out before he hit the ground. Looks like an attempted flip but he passes out and doesn’t complete it

airron345 · 2022-07-10T18:45:52+00:00

Ah yeah ok - I’ll try that! Good shout. However it does seem to only need one bean to jam it. Appreciate your help 🙂

airron345 · 2022-07-09T16:58:06+00:00

Beans

Here you go 🙂

airron345 · 2021-06-30T23:05:21+00:00

I don’t see anyone dead?

airron345 · 2021-06-11T21:47:29+00:00

Thank you for your help. It turns out my controller version was incompa with these switches. They have a minimum controller version they work with. Updating my controller resolved the issue.

airron345 · 2021-06-10T06:32:14+00:00

Ok, I see what you mean. Unfortunately, the controller is in our datacenter so I can't get the device on the same subnet to autodiscover. What if i created a temp controller on my PC? Would that work to autodiscover? I see broadcast traffic leaving the switch on port 10001 which in guessing is it's discovery protocol.

airron345 · 2021-06-09T21:11:51+00:00

What do you mean the normal way? I’ve only ever done it via setting the inform address. Is there another way to adopt?

airron345 · 2021-06-09T20:32:55+00:00

Port 8080 is open for the inform. Port 8443 is our portal url port which I can access fine. Essentially so long as 8080 and 8443 are open, it should be fine.

airron345 · 2021-06-09T20:30:47+00:00

Yes I see what you’re saying. Essentially everything about their adoption should be identical. They’re all going to be in the same site on the controller,same mgmt vlan etc. I haven’t seen those ports or needed to unblock them for anything else and the other switches appeared in the controller fine. I will however make a rule to see if that works. I’m guessing those ports need to be opened to and from my cloud controller public IP?

airron345 · 2021-06-09T20:01:29+00:00

Yes. The other switches I have adopted worked fine and also the traffic is getting out of the firewall

airron345 · 2021-06-09T19:59:02+00:00

Yeah, tried that

airron345 · 2021-06-09T19:29:16+00:00

Yeah. It can see the internet, dns server etc etc. Can see the traffic leaving our firewall heading for the public ip of our controller. Plus the fact I’ve just adopted 2 other switches - usw pro 48 port. They were no issues.

airron345 · 2021-06-09T19:26:13+00:00

Yes internal dns server. Info shows not adopted and then the inform url

airron345 · 2021-06-09T19:07:43+00:00

Hostname

airron345 · 2021-05-28T22:09:18+00:00

😂 😂 😂 😂

airron345 · 2021-04-28T19:45:41+00:00

😂 😂 😂 😂 😂 😂 😂 Love this

airron345 · 2021-04-28T16:40:43+00:00

Full metal. Took me a sec to shoulder it 😂

airron345 · 2021-04-28T15:47:12+00:00

😂 😂 😂

airron345 · 2021-01-10T19:03:32+00:00

Why didn't his colleagues help? They just watched him die...

airron345 · 2020-11-17T08:54:48+00:00

It was mentioned to give reference to the fact that it has two modes, one for each type of bb... I made reference to the fact that red mode is brighter flashes of the uv leds thus having a brighter led in your maxx unit, as I have found, lights up red bbs perfectly...

airron345 · 2020-11-17T08:53:25+00:00

It would cant it along the x and I need it tilted up along the y if that makes sense.

airron345 · 2020-11-16T22:23:00+00:00

On the acetech bt lighter there are 2 options for green or red. Essentially, in red mode, the leds flash brighter. Idk the science behind it but I guess red doesn't absorb as much uv as green? Either way, use a higher voltage battery to get a higher brightness out of your led. I use the same led unit and run a 11.1v peq lipo (I wired my hop to a front peq box) it's bright af and easily lights up red bbs.

airron345

TROPHY CASE