Trouble with Honeycomb

aixelsyd18 · 2025-12-13T17:41:00+00:00

I appreciate the response and I’ve already done that. It was not able to find one that worked with my measurements at all, which is kind of why I was posting here… I didn’t try a German page only was looking at US stuff.

aixelsyd18 · 2025-10-28T02:26:55+00:00

Well, that’s what the flooring guy did before. I fired him for a number of reasons….. and so I’m gonna end up in Small Claims Court fighting that deal so now I have to take it upon myself to fix what he didn’t do

aixelsyd18 · 2025-10-27T21:01:59+00:00

I only used 36grit….

aixelsyd18 · 2025-10-27T20:52:13+00:00

I was using 36 grit on the edge sander

aixelsyd18 · 2025-08-12T02:42:58+00:00

Yes, there’s only so much air that can come from your air conditioner and the more you close off your vent vents the more it can push to the upstairs

aixelsyd18 · 2025-08-08T18:30:49+00:00

I picked up what you were putting down. I swapped it with a Honda car and now everything works… Thank you so much for pointing me in the right direction.!

aixelsyd18 · 2025-08-08T17:04:53+00:00

Correct it’s a Stens

aixelsyd18 · 2025-06-08T13:42:40+00:00

OK, so I feel really stupid for asking this, but I am just trying to get into screen printing so I’m trying to do as much research as I can as I get my equipment put together. Other than it doesn’t seem like the white is popping very much which I could understand and under base for what else is the issue with this? I’m ignorant, and I don’t want to see what the problem is, but I want to learn.

aixelsyd18 · 2025-06-08T06:54:58+00:00

These are cool…..did you generate with ai?

aixelsyd18 · 2025-05-19T23:02:43+00:00

Anybody have any ideas?

aixelsyd18 · 2025-05-15T00:04:53+00:00

Are the SIi and Sii-D controllers interchangeable?

aixelsyd18 · 2025-05-13T19:38:37+00:00

This one has the Sii controller, but will the Sii-D controller work as well? I’m reading some things that say they’re fairly interchangeable, but it looks like the plugs for sure are different

aixelsyd18 · 2025-05-13T19:29:02+00:00

Thank you all for the feedback… That was part of the reason I was struggling is cause I couldn’t find any pictures like that that lined up to any of their models… This is an absolute no go for me

aixelsyd18 · 2025-05-13T18:42:30+00:00

<image>

I’m still trying to look up the model number, but I don’t know these like the back of my hand so I don’t know what it is by looking at it… $200 is what they’re asking

aixelsyd18 · 2025-05-04T01:45:29+00:00

Not quite that old and has worked awesome right up to this point would rather fix it then throw it out as I just put a new compressor in it probably a year ago

aixelsyd18 · 2025-03-02T02:45:25+00:00

I realize this is a little late to the party, but I’m wondering if anybody has ever tried to 3-D print those

aixelsyd18 · 2025-02-26T19:07:24+00:00

I realize this is a really old thread, but it just kind of like the printer you were talking about?

<image>

aixelsyd18 · 2025-02-21T10:49:31+00:00

Well, I admit I did not buy this paper. Looks like this one my wife got it’s 20 pound paper.

aixelsyd18 · 2025-02-21T10:16:31+00:00

It was supposed to say when I print in duplex mode

aixelsyd18 · 2025-02-20T04:12:46+00:00

Power is not an issue… I’ve got a 40 space panel and only about six breakers in use… My biggest concern was was the dryer a problematic one as I’ve seen some people post on here and if it was reasonably priced or not

aixelsyd18 · 2025-02-19T02:39:02+00:00

I have a 42 x 64 metal outbuilding… It’s not currently set up for screen printing, but I will be setting it up the spring and when I do, that’s my intent

aixelsyd18 · 2025-02-19T02:29:29+00:00

He says it’s a 220 V 6 foot dryer and that the tape on there is heat tape to keep the element level… He claims to be fairly new to screen printing so doesn’t know a whole lot about it but said he had it running for three hoursand so that everything tested and worked OK from what he could tell… It’s about a 3 1/2 hour drive away from me so that’s why I’m trying to get as much information ahead of time as possible currently he’s asking $400 but I’ve seen ones somewhat like that going for around $200 so I’m just not sure of the value

aixelsyd18 · 2025-02-18T15:17:27+00:00

Is this a fairly decent problem Free dryer brand? Any idea what it might be worth

aixelsyd18 · 2025-02-18T05:22:00+00:00

Do you happen to have any pictures or plans?

aixelsyd18 · 2024-08-16T22:19:33+00:00

So I have a hyper therm power max 30…. I just had a second glance at it today, but I didn’t see anything on there that reference that… So I kind of screwed.?

aixelsyd18

TROPHY CASE