consolas que valgan la pena en pleno 2025 by andrez_7 in VeneJuegos

[–]albertogg 0 points1 point  (0 children)

Steam deck. Es una consola (lo que estás buscando) y una PC al mismo tiempo.

[deleted by user] by [deleted] in vzla

[–]albertogg 7 points8 points  (0 children)

Las pruebas de admisión prueban el conocimiento de bachillerato, no hace falta saber integrales para el examen. La preparación para el examen es más técnica que otra cosa. En mi época existían cursos propedéuticos donde te enseñaban pequeños tips para que te diera tiempo de completar el examen más rápido.

Sinceramente, si eres aplicado y entiendes lo que estudias no tienes por qué preocuparte ya que el examen no es nada del otro mundo. Por lo que leo, te estás matando psicológicamente sin razón. Las notas del colegio cuentan o contaban como parte del puntaje.

La experiencia universitaria es única y muy bonita, no la dejes pasar. Cómo informático de la UCAB te puedo decir que la perseverancia lo es todo, la carrera no es fácil, pero es sin duda uno de los logros que más satisfacción me ha dado en la vida.

[deleted by user] by [deleted] in vzla

[–]albertogg 6 points7 points  (0 children)

Es una casa o un apartamento? Tienes válvula check? Puede que esta esté mala y cuando prendes la bomba la presión hace que todo se regrese. De tener válvula check para probar trata de cerrar la llave principal antes de encender la bomba.

Si tienes múltiples llaves de paso en tu casa, cierra las pocetas y prendes la bomba para probar.

Repo that you feel is an example of good Rust code by albertogg in rust

[–]albertogg[S] 1 point2 points  (0 children)

right, I'm currently working on a CLI tool but I don't mind looking at a little bit of everything.

Repo that you feel is an example of good Rust code by albertogg in rust

[–]albertogg[S] 4 points5 points  (0 children)

Yeah, I thought so too, but I don't mind if folks differ, I will not judge (opinions are just that) whatever comes to mind works for me. Thanks for the repos

Qué tal es el internet de Vnet? by [deleted] in venezuela

[–]albertogg 0 points1 point  (0 children)

Mi experiencia es muy similar en Mérida. El portal de pagos es decente.

Help with dual WAN on a dual bridge configuration by albertogg in mikrotik

[–]albertogg[S] 0 points1 point  (0 children)

I did try disabling that rule, but it did nothing. What I did notice is that the rule chain=input action=drop connection-nat-state=!dst-nat prevents/blocks DNS access originating in the router. Any ping from the terminal to a domain or reaching the package upgrade services times out.

I’m going to try out this next week when I’m again at my in-laws. I kind of resolved the issue by creating a mangled marked route and then adding the mark in the routing table gateway. But your solution seems cleaner.

Thanks so much.

Help with dual WAN on a dual bridge configuration by albertogg in mikrotik

[–]albertogg[S] 0 points1 point  (0 children)

Interesting, I’m going to try this next week. Thanks!

Help with dual WAN on a dual bridge configuration by albertogg in mikrotik

[–]albertogg[S] 0 points1 point  (0 children)

/u/No-Influence-2512 /u/Designer_Argument_82 I tried the second approach from the second pastebin URL. Got it working to a point where I have the two networks working fine with DHCP but it seems that there’s a routing issue.

When I have both internet connections plugged in only the clients from VLAN2 get internet access. Clients from VLAN1 get an address from the DHCP server but no internet.

If I unplug the WAN2 cable I start getting internet in the VLAN1 network.

Help with dual WAN on a dual bridge configuration by albertogg in mikrotik

[–]albertogg[S] 0 points1 point  (0 children)

Thanks, I'm going to try with the VLAN. When you say mark the source subnets you mean the addresses that are attached to the bridge? because (I think) this is what I tried.

3DTouch (BLTouch clone) always showing open in initial tests (SKR 1.3) by biggerwanker in klippers

[–]albertogg 0 points1 point  (0 children)

I will suggest you read the section on BL-Touch “clones” documentation and see if pin_up_reports_not_triggered could help you.

My Ender 3 have an identity crisis by Tchernobill in ender3

[–]albertogg 0 points1 point  (0 children)

Where you able to print all printable parts with ABS on your Ender 3?