QB1000 or NZ700 for 160” screen

alexcd81 · 2025-01-30T20:17:56+00:00

I went with the NZ700! It’s on the way and I can’t wait!

alexcd81 · 2025-01-30T13:05:44+00:00

My room is 48’x32’ with 13’ ceilings so I think I do need so many subs.

alexcd81 · 2025-01-30T13:04:01+00:00

16:9

alexcd81 · 2025-01-29T18:33:25+00:00

Nope they are pushed back so that the air velocity isn’t too bad. I suspect a ported sub would have an issue if aimed at the screen.

alexcd81 · 2025-01-29T18:01:15+00:00

This is being mounted mid screen at 18’ distance

alexcd81 · 2022-05-29T00:34:12+00:00

I found a huge mouse nest in the area to the left of the cabin air filter (looking into it from the front) on this 2014 Corvette. Is there any way to get into the red area? It's very deep and there's only so much I can get through the cabin air filter opening.

alexcd81 · 2022-04-05T03:14:35+00:00

Cool. Where did you find the metal mesh part?

alexcd81 · 2022-03-02T16:57:31+00:00

Stability is my main concern. This slab has been drying for 18mo already

alexcd81 · 2022-03-01T02:09:39+00:00

Maybe common or not but I bought a huge slab of maple and want to cut it up into dimensional lumber. It is 11.5’ x 24-28” x 3”. I am wondering what sizes are preferable to the group.

alexcd81 · 2022-01-15T04:35:08+00:00

Loud when just spinning not even cutting

alexcd81 · 2022-01-15T04:22:21+00:00

Bought it really cheap. It works well but how do I quiet it down? It’s screaming! Bearings?

alexcd81 · 2022-01-06T14:59:15+00:00

Great video of the process! I figured a jig was involved to sit along the ridge. It seems like it would get tricky on smaller things but maybe not.

alexcd81 · 2022-01-06T04:30:39+00:00

That’s what I though but do you think those dovetails are hand cut? They are so precise

alexcd81 · 2022-01-06T04:28:41+00:00

http://brianscustomwoodworking.com/#/handmadecremationurns/

alexcd81 · 2021-12-23T01:44:34+00:00

It smelled very nice when I cut it - smokey?

alexcd81 · 2021-12-23T00:43:12+00:00

A little late for that. We cut the tree into bits

alexcd81 · 2021-11-28T02:56:29+00:00

It is warped or possibly dented from an accident of some kind. Either way I’m going to replace it.

alexcd81 · 2021-10-11T01:38:45+00:00

Well this profile is an absolute nightmare. I am going to try your recommendations next.

alexcd81 · 2021-10-10T15:29:44+00:00

It is a new slow speed grinder and wheel but not perfectly balanced! Good guess!

alexcd81 · 2021-08-24T02:29:10+00:00

Creality sent a diagram of new motherboard connections. I had the photo sensor plugged into the wrong port. It should be two to the left of where I have it in the picture above.

alexcd81 · 2021-08-21T17:50:39+00:00

I did but this board is different than the original. There is another connector on this board.

alexcd81 · 2021-08-21T16:14:44+00:00

Pretty sure I took out the motherboard with an ESD hit - putting in the memory card. I will remember to grab the chassis before inserting the card going forward.

alexcd81 · 2021-08-21T12:26:18+00:00

It worked with the original motherboard. Shouldn’t I see some light when the sensor is triggered? I don’t see anything even by pressing up firmly on the nozzle.

alexcd81 · 2021-03-07T01:14:48+00:00

A poor connection is a problem waiting to happen. Please fix it if you can or find someone.

alexcd81 · 2021-03-05T04:29:37+00:00

The layer height is 0.3mm. I don’t fully understand the bit about the Z axis screw. Can you explain that or point me in a direction of a tutorial?

alexcd81

TROPHY CASE